![background image](http://html1.mh-extra.com/html/gbc/streamwire/streamwire_service-manual_3988657284.webp)
GBC StreamWire
7/23/2020
Repairs/Adjustments
4-187
ADJ 1.7 Interlock Flag Adjustment
If a CLOSE DOOR, CLOSE TRAY, or CLOSE LID message is shown
even when the door is closed, or the message occurs during operation, it
may be necessary to adjust the Interlock Flag.
Inspection Procedure
1) Check to see if the CLOSE DOOR, CLOSE TRAY, or CLOSE LID
message is shown even when the door is closed. If the message is
shown when the door is closed, or you need to press extra hard on
the door to make the message go away, the interlock flag may need
adjustment.
2) If the CLOSE DOOR, CLOSE TRAY, or CLOSE LID shows up during
operation, or occurs intermittently, the interlock flag may need
adjustment.
3) If scoring is noticed on the interlock switch due to the interlock flag
rubbing on the hub of the interlock, the interlock flag may need to be
adjusted.
4) If the door does not appear to close all the way, but sticks out near
the interlock location, the Interlock Flag may need adjustment.
5) Visually inspect the Interlock Flag position when the door is closed.
The Flag should stop 1-2 mm from bottoming out.
Adjustment Procedure
1) Open the door and locate the Interlock Flag. This is the metal
component that presses the Interlock switch to keep it closed.
2) If the interlock is hitting the side rails of the interlock, loosen the M3
Screws (2) shown in red securing the Interlock Flag to the Adjustment
Plate.
3) If the flag needs to press the interlock in more or be pulled back to
allow the door to fully close, loosen the M3 Screws Nuts (2) shown in
yellow securing the Adjustment Plate to the door.
4) Shift the Flag Plate forward, back, or laterally as needed to adjust the
resting position of the Interlock Flag Plate within the Interlock Switch.
The flag should be 1-2 mm short of bottoming out on the Interlock
Switch when in the resting position and centered between the rails.
5) Tighten the screws and close the door to confirm the Interlock is
operating as expected.
ADJ 1.8 Element Hook Position Adjustment
Summary of Contents for StreamWire
