![background image](http://html1.mh-extra.com/html/gbc/streamwire/streamwire_service-manual_3988657376.webp)
GBC StreamWire
07/23/2020
General Procedures and Information
6-39
GP 6.4.6
Check S47, S48
Use the information in this section to locate the appropriate sensor(s) on
the eWire. If the sensor does not operate as expected, follow the
troubleshooting steps located in this section to fix the faulty sensor.
Locate Sensor S47 and S48:
•
S47 and S48 are located inside the Closer Module
Check Sensors Procedure (Sensors S47 & S48):
1. Do REP 6.4 to remove the Closer Motor
2. Do REP 6.1 to install the Closer Module, but leave the Closer Motor
detached.
S48. Rotate the large gear by hand and watch for S47 and S48 to
change states. If this is difficult, hold the jaws together with a
separate hand while the gear is rotated.
Both Sensors are working properly
Yes
- Do REP 6.4 to reinstall the Closer Motor and return to the
procedure that directed you here;
No
- Go to Step 4
4. Check that the Flat Mylar Closer Cable is plugged in and properly
seated in its housing as shown.
Both Sensors are working properly
Yes
- Do REP 6.4 to reinstall the Closer Motor and return to the
procedure that directed you here;
No
- Go to Step 5
5. Check that the sensor wires are connected securely at the Sensor
headers and at the Main Control Board B (PL 5.27). Do REP 1.5 to
remove the Rear Cover to gain access to the connector at the Control
Board. Refer to Section 7 Wiring and GP 6.22
find the Cable termination locations.
Both Sensors are working properly
Yes
- Do REP 6.4 to reinstall the Closer Motor and return to the
procedure that directed you here;
No
- Go to Step 6
6. Replace the Sensor/s with a known good sensor of the same type (PL
to verify the operation of the sensor you are
going to use before installing it in the S47 or S48 slot.
Both Sensors are working properly
Yes
- Do REP 6.4 to reinstall the Closer Motor and return to the
procedure that directed you here;
No
- Go to Step 7
7. Inspect the Disk Encoder (PL 5.9). The disk should be positioned in
the middle of the S48 sensor. The disk should be flat and should not
be loose from the collar. Correct any of these problems and do REP
6.9 Disk Encoder Replacement if needed.
Summary of Contents for StreamWire
