GBC StreamWire
07/23/2020
General Procedures and Information
6-45
GP 6.5.4
Check M8
To access motor M8:
•
Open the door and slide out the Element Feeder.
•
Do
•
Insert a cheater into the element feeder door interlock switch
1. Do
to check that the Rewind Spool
rotates when Motor M8 is activated.
The Motor operates as expected
Yes
- Return to the RTP that directed you here
No
- Go to Step 2.
2. Make sure the motor wire is connected securely at the header and at
the Main Control Board (PL 5.27). Do REP 1.5 to remove the Rear
Cover to gain access to the connector at the Control Board. Refer to
REP 3.9 to access the M8 Motor connection.
All the connectors are securely connected.
Yes
- Go to Step 3
No
- Make the connection and resume operation
3. Inspect the round belt for damage. Remove Element Feeder rear
cover to access the belt.
Belt is okay
Yes
- Go to Step 4
No
- Replace the spindle drive assembly 7718107, Refer to REP 3.9.
Repeat Step 1.
4. Check the tightness of the set screw of the pulley on the motor shaft.
Check tightness of the set screw on the connected pulley.
All the set screws are secured tightly
Yes
- Go to Step 5
No
- Tighten the loose set screw and repeat Step 1.
5. Check that the cable(s) connecting the Motor to the Main Control
Board are intact. Refer to the motor cables table to identify the
appropriate cable part numbers,
The cables look okay
Yes
- Go to Step 6
No
- Replace the faulty cable and resume normal operation
firmware for the eWire
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 7
7. Replace the faulty motor. Refer to REP 3.9, Spool Rewind Motor
Replacement.
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 8
8. Replace the cables from the motor to the Main Control Board. Refer
to GP 6.24 for cable part numbers.
This clears the fault
Yes
- Resume normal operation
No
- Go to Step 9
9. Replace Main Control Board, B (REP 11.2)
This clears the fault
Yes
- Resume normal operation
No
- Escalate to second level
Summary of Contents for StreamWire
