GBC StreamWire
07/23/2020
General Procedures and Information
6-33
2. Make sure the sensor wire is connected securely at the Sensor and at
the Main Control Board (PL 5.27). Do REP 1.5 to remove the Rear
Cover to gain access to the connector at the Control Board. Refer to
Section 7 Wiring and
to find the Cable termination locations.
All the connections are made securely
Yes
- Go to Step 3
No
- Make the connection and repeat Step 1.
3. Replace the Sensor with a new one (alternatively, swap the sensor in
the faulty position with a sensor from a different good position to
check if it is a bad sensor).
Replacing the sensor corrects the issue
Yes
- Use the new sensor and return to normal operation
No
-
Go to Step 4
4. Visually inspect the Cable from the sensor all the way to the Control
Board (PL 5.27). If the Cable is damaged, replace the Cable. See
Section 7 and GP 6.22 for cable part numbers and locations.
Sensor cable looks okay
Yes
- Go to Step 5
No
-
Go to Step 6
5. Do
GP 6.3.
5 FIRMWARE UPGRADE Procedure to Re-flash the
firmware for the eWire.
Re-flashing firmware clears the fault
Yes
- Resume normal operation
No
- Go to Step 6
6. Do REP 11.2 to replace the Main Control Board (PL 5.27).
This clears the fault
Yes
- Resume normal operation
No
- Escalate to second level
GP 6.4.4
Check S21, S22, S25, S42
Use the information in this section to locate the appropriate sensor(s) on
the eWire. Once you have located the sensor, follow
the function of the sensor. If the sensor does not operate as expected,
follow the troubleshooting steps located in this section to fix the faulty
sensor.
Locate Sensor S21:
•
Slide the Element Feeder Drawer all the way out of the eWire.
WARNING
Moving Parts, keep hands clear of all moving parts when
the Interlock Cheater is inserted. Keep fingers away from
the Knife Mechanism when power is on.
See Section 0,
page vii for other languages.
•
To check S21, feed a piece of wire through the knife area
using the manual advance knob.
Summary of Contents for StreamWire
