![background image](http://html1.mh-extra.com/html/gbc/streamwire/streamwire_service-manual_3988657396.webp)
GBC StreamWire
07/23/2020
General Procedures and Information
6-59
GP 6.6.4
Check L8 Holder Lock Solenoid
To access Solenoid L8:
•
Open and close the Top Cover to home the Holder Module.
•
There are two L8 solenoids located on the Holder Module, refer
to PL 5.22.
•
Insert a cheater into the Top Cover Interlock.
WARNING
Moving Parts, keep hands clear of moving parts when
the Interlock Cheater is inserted.
See Section 0, page
vii for other languages.
to activate and deactivate Solenoid
L8
•
Unplug one solenoid and perform the check, then plug that
solenoid back in and unplug the other and repeat the check.
The plugged in solenoid in either case should still trigger
even if it does not move the holder. Plug both back in.
•
The holder lock mechanism should cycle closed and open
when L8 is activated
•
Note that both the front and back solenoids should cycle
when activated
Holder Lock mechanism cycles forward and back when L8 is
cycled
Yes
- Return to the RTP that directed you here;
No
- Go to Step 2
2. Make sure the solenoid wire is connected securely at the header and
at the Main Control Board (PL 5.27). Do REP 1.5 to remove the Rear
Cover to gain access to the connector at the Control Board. Refer to
GP 6.26 for termination locations.
All the connectors are securely connected.
Yes
- Go to Step 3;
No
- Make the connection and resume operation
3. Check that the cable(s) connecting the Solenoid to the Main Control
Board are intact. Refer to the solenoid cables table to identify the
appropriate cable part numbers, refer to
The cables look okay
Yes
- Go to Step 4;
No
- Identify and replace the faulty cable
4. Do
GP 6.3.5
firmware for the eWire
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 5
5. Replace 7717746 Holder Lock Solenoid L8, refer to REP 8.19
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 6
6. Replace 7716612 Holder Lock Assembly, refer to REP 8.17 Holder
Lock Sub-Assembly Replacement
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 7
7. Do
REP 11.3 Main Control Board B Replacement.
This clears the fault
Yes
- Return to normal operation;
No
- Escalate to second level
Summary of Contents for StreamWire
