GBC StreamWire
07/23/2020
RTPS
2-27
4 WIRE JAM CODES
RTP 4.1 J320- S20 SPOOL ELEMENT SLACK TIMEOUT
S20 Element Slack time out is the maximum time to wait for
S20_Element_Slack sensor to detect a wire.
1. Check if the rewind paper from the spool has been
cut/damaged/slipped.
Rewind paper appears to be damaged/cut
Yes
- Clear the Rewind Spool and reinsert the rewind paper;
No
- Go to Step 2
2. Check that the element shield is properly installed and not rubbing
against the spool. Ensure that the 2 studs on the shield are tight and
are fully seated into the slots.
Shield is properly installed
Yes –
Return to normal operation
No-
Go to step 3
3. Perform GP 6.13 to clean the base of the Element Feeder Drawer.
Ensure that the Element Slack Detect Assembly moves freely without
any obstruction.
This clears the fault
Yes
- Return to normal operation;
No
- Go to step 4
4. Perform GP 6.7 and GP 6.8 to reinstall the Supply Spool.
Replacing the spool with a new one fixes the problem
Yes
- Reinstall the correct size spool and continue operation;
No
- Go to Step 5
5. Do GP 6.4 to check S20 Element slack sensor.
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 6
6. Do GP 6.5 to check M8 Spool rewind motor.
This clears the fault
Yes
- Return to normal operation;
No
- Go to step 7
7. Check the Rewind Belt Pulley (Green Belt)
Pulley is intact and has proper tension
Yes
- Go to Step 8;
No
- Do REP 3.9 to replace the Pulley Assembly
8. Perform ADJ 1.2 Element Slack Detection Adjust.
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 9
9. Check the condition of Element Slack Detect Assembly (PL 5.10)
Element Slack Detect Assembly is in good condition
Yes
- Go to Step 10;
No
- Do REP 3.18 to replace Element Slack Detect Assembly.
10. Do GP 6.3.5 FIRMWARE UPGRADE Procedure to Re-flash the latest
firmware for eWire.
This clears the fault
Yes
- Return to normal operation;
No
- Escalate to second level
Summary of Contents for StreamWire
