GBC StreamWire
07/23/2020
RTPS
2-52
RTP 5.10 J380- CLOSER JAWS HOME TIMEOUT
J380 is triggered if it takes longer than the specified time for the Upper
Jaw to move to its home position and change the state of S47 Closer Full
Open.
1. This may be caused by the closer cams being out of phase. A
symptom of this would be an increasing level of elements being
closed unevenly. To check this, remove the Front Closer Cover and
the Top Closer Cover by removing the M4 screws (3)
With this cover removed and the cams visible, perform GP 6.3.3 to
active M20. Watch the cams rotate.
Are the cams rotating in phase?
Yes
–
Go to step 2;
No
–
Perform ADJ 1.11 Closer Cam Phase Adjustment.
2. Remove the M3 Screws (2) holding the Cable Access Cover. Check
that the Flat Mylar Closer Cable is plugged in and properly seated in
its housing as shown.
Cable is plugged in and properly seated
Yes
- Go to Step 3;
No
- Plug in the cable close all covers and cycle the Element Feeder
Door interlock.
This clears the fault
Yes
- Reinstall the Cable Cover and return to normal operation;
No
- Go to Step 2.
3. Check the area exposed in step 1 for debris i.e. screws, elements, or
other foreign objects
Closer cam and chain areas are free of foreign objects.
Yes
- Go to Step 4.
No
- Remove the object(s). If the debris is unable to be removed, do
REP 6.4 to remove the M20 Closer Motor. Rotate the large
drive gear by hand to rotate the cams and chain and release
any objects. If the debris is still unable to be removed, escalate
to second level.
This clears the fault
Yes
- Reinstall the covers and return to normal operation;
No
- Go to Step 4.
4. Do GP 6.5 to check M20 Closer Motor.
This clears the fault
Yes
- Return to normal operation;
No
- Go to step 5.
5. Do GP 6.4 to check S47 Closer Full Open.
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 6.
Summary of Contents for StreamWire
