Repairs/Adjustments
07/23/2020
GBC StreamWire
4-30
9. Using a scale, adjust the solenoid so that the diverter has lifted
5mm to 6mm above the lower paper path shown below:
When L1 is deactivated, the diverter should be below the plane of the
paper path as shown below
10. After adjusting the diverter, tighten the M4 screws(2) loosened in
step 7
11. Re-install the Lower Bypass Rear Cover.
12. Do REP 1.1
13. Connect the Power Cord
14. Turn ON the eWire.
REP 2.19 Solenoid Replacement, Disengaging Roller #1 and #2 (L2 &
L3)
PARTS LIST ON PL 5.3
Use this procedure to remove and install the Disengaging Roller #1 and
#2 Solenoids. Solenoids L2 and L3 are part of the same sub-assembly
(7717125) and must be replaced together.
Removal Procedure
WARNING
Do not perform repair activities with the power on or electrical power
supplied to the machine. Some machine components contain
dangerous electrical voltages that can result in electrical shock and
possible serious injury. See Section 0, page vi for other languages.
1. Switch power OFF to eWire.
2. Disconnect the Power Cord.
3. Open the top cover and lift the lower paper path.
4. Do REP 2.4
Idler Roller Replacement, Paper Path
Idler Roller Assembly on the left and right side of the Disengaging
Roller #1 and #2 sub-assembly (7717125).
5. Disconnect the Cables at the header and remove Cables from the
wire clamps on the sub-assembly.
Summary of Contents for StreamWire
