![background image](http://html1.mh-extra.com/html/gbc/streamwire/streamwire_service-manual_3988657290.webp)
GBC StreamWire
7/23/2020
Repairs/Adjustments
4-193
ADJ 1.11 Closer Cam Phase Adjustment
Use the following procedure to correct the phase of the cams in the closer
when binding closes unevenly.
Adjustment Procedure
1) Remove the Front Closer Cover and the Top Closer Cover by
removing the M4 screws (3).
2) Cheat the Top Cover Interlock.
3) Do GP 6.3.4 and perform the Feed Element and the Full Close
Function Test. Inspect the rear side of the element to determine if it is
under or over closed.
Service Settings Menu
Function Tests
Feed Element
Full
Close
4) Do GP 6.3.4 and perform the Closer ADJ Pos Function Test. This will
allow access to the M5 Screw in the Clamping Collar shown below:
Service Settings Menu
Function Tests
Closer Cycle
5) Loosen the M5 Screw in the Clamping Collar, do not remove it fully.
6) Leave the hex key in the Clamping Collar Screw and hold it in
position. Using a 7mm wrench, on the flat of the shaft, rotate the shaft
in the direction needed to correct the uneven binding. If the closer
shaft does not have flats, the adjustment must be made by pushing
on the rear cam in the required direction.
7) When looking at the front of the Closer Module, rotate the rear shaft
(or cam) counter-clockwise if the rear side of the element is over
closed and clockwise if it is under closed. Take note that a small
adjustment will have a large impact on the closing of the rear side of
an element.
8) With a hex key inserted, push the hex key toward the rear of the
machine while tightening the M5 Screw to a torque of 6Nm. Note: If a
torque wrench is unavailable, use the leverage of a nut driver to
achieve the proper torque.
9) Cycle the Top Cover Interlock. Note: Take care to remove the hex key
before cycling the interlock.
10) Repeat steps 3 – 7 until the rear of the element is closed to the same
amount as the front.
11) Reinstall the Top Closer Cover and the Front Closer Cover with the
M4 Screws (3).
12) Return to the procedure that directed you here.
Rear shaft
Rear cam
Summary of Contents for StreamWire
