GBC StreamWire
07/23/2020
RTPS
2-49
7. Do GP 6.5 to check M15 Holder linear drive motor
This clears the fault
Yes
- Return to normal operation;
No
- Go to step 8
8. Inspect the springs for the Holder gates (PL 5.21).
Holder gates springs are present and not damaged
Yes
- Go to Step 9;
No
- Replace the missing/damaged spring
9. Go to RTP 5.20, Step 5 and 6 to ensure the Holder rotate
components are in good order.
Holder rotate components are in good order
Yes
- Go to Step 10;
No
- Follow steps in RTP 5.20 to take the necessary corrective action
10. Do GP 6.3.5 FIRMWARE UPGRADE Procedure to Re-flash the
firmware for eWire.
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 11
11. Do REP 11.2 “B” Main Control Board Replacement
.
This clears the fault
Yes
- Return to normal operation;
No
- Escalate to second level
RTP 5.5 J374- S46 BOOK DROP TIMEOUT
J374 is triggered when it takes longer than the specified time for the
Closer to reach S46 Closer Home after the book is ejected.
1. Do GP 6.4 to check S46 Closer Home Sensor.
This clears the fault
Yes
- Return to normal operation;
No
- Go to Step 2
2. Check the Condition of the Closer Linear Drive Belt (PL 5.21).
The timing belt is in good condition. There are no missing teeth
and the belt is not frayed
Yes
- Go to Step 3;
No
- Replace the damaged timing belt (REP 8.10) and resume
operation
3. Check the tension of the Closer Linear Drive Belt (ADJ 1.6).
The tension of the timing belt is good
Yes
- Go to Step 4;
No
- Do to ADJ 1.6 to set the belt tension and resume operation
4. Check if the set screw on the Closer motor pulley and the screws in
the drive components are sufficiently tight.
The screws are tight
Yes
- Go to Step 5;
No
- Tighten the loose set screw(s) and resume operation
Summary of Contents for StreamWire
