background image

 
 

BALNAFETTACH HOUSE, PH26 3LW             (01479) 872 518                   [email protected]

 

 

 

MicroFogger 3 Lite -

 

User Manual 

(V1.10 Dec21) 

Initial Preparation 

 IMPORTANT Please Read! 

Turn MF3 

“ON” using the rocker switch 

BEFORE attaching the charging cable, 

Put the included USB charging cable into a USB charger socket outlet and Then connect 
USB charging cable to the MF3. 

Only use a wall socket/mains supplied type of USB charger to ensure the unit charges fully 
and also to prevent unintentional activation during charging. 

Allow the MicroFogger to fully charge before beginning to use it. This can take up to 6 hours. 

See page 3 for colours of LED lights during charging etc 

 

 

NOTE

:  The MF3 Lite will only accept charge if it has been turned on as described above. 

 

 

Carefully unscrew the black fluid tank (see image bottom right) by turning anti-clockwise 

 

 

Double check that a coil is installed (it usually is) 

 

 

Using the 50ml bottle of fog liquid, unscrew bottle cap. Using the pipette-style tip, 
carefully pour fog liquid into the 

gap

 between the inner and outer walls of the reservoir.  

DON’T pour into the central part (

coloured RED in image)

.  D

on’t 

squeeze the bottle too 

hard 

 

or you’ll overfill and spill the liquid

!  

 

 

Keep filling the fluid tank until the liquid is at the 
same level as the top of the interior metal wall. 

 

 

At this stage 

 with fingers 

 check the coil (small 

silver cylinder) is firmly screwed into place (good 
finger tight!) 

 

 

Holding the reservoir tank upright, 

invert

 the MF3 body on to 

it and screw the body on to the tank (again, 

good finger tight

).  

Turn the MF3 back to the upright position.

 

 

 

 

Now make a cup of tea/coffee as you should 

let the MF3 Lite 

rest upright for a minimum of 30 mins

 (this ensures that the 

liquid properly seeps into the new heating coil).  The coil may 

be damaged if you don’t wait the 30 mins

  

 

 

 

 

Summary of Contents for MicroFogger 3 Lite












Reviews: