manualshive.com logo in svg

Dell S6100, Configuration Manual

The Dell S6100 Configuration Manual is a comprehensive guide that enables users to maximize the functionality of their Dell S6100 device. This manual can be easily downloaded for free from our website, allowing users to access valuable information and optimize their product experience.

Share
Download
background image

Te 1/1/1/1 Aggressive  10         Admin Shutdown

Te 1/1/2/1 Aggressive  10         Admin Shutdown

Te 1/1/3/1 Aggressive  10         Admin Shutdown

Te 1/1/4/1 Aggressive  10         Admin Shutdown

Te 1/1/5/1 Aggressive  10         Admin Shutdown

Te 1/1/6/1 Aggressive  10         Admin Shutdown

Te 1/1/7/1 Aggressive  10         Admin Shutdown

Te 1/1/8/1 Aggressive  10         Admin Shutdown

Dell#

Related Commands

•

fefd

 — enable far-end failure detection.

•

fefd disable

 — disable FEFD on an interface only.

•

fefd-global

 — enable FEFD globally on the system.

•

fefd reset

 — reset all interfaces or a single interface that was in “error-disabled” mode.

954

Layer 2

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

3Com SuperStack II Important Information preview
SuperStack II
Brand: 3Com Pages: 2
3Com CoreBuilder 5000 Quick Start And Reference preview
CoreBuilder 5000
Brand: 3Com Pages: 16
3Com CoreBuilder 9000 Quick Installation Manual preview
CoreBuilder 9000
Brand: 3Com Pages: 24
KELCO D40 Installation And Operating Instructions preview
D40
Brand: KELCO Pages: 2
KELCO F21 Series Installing And Operating Information preview
F21 Series
Brand: KELCO Pages: 4
Oase Underwater Switch 24V DC/DMX/02 Operating Instructions Manual preview
Underwater Switch 24V DC/DMX/02
Brand: Oase Pages: 40
Ihse Draco major K474-U8/C8 User Manual preview
Draco major K474-U8/C8
Brand: Ihse Pages: 167
steute Ex 95 SB Mounting And Wiring Instructions preview
Ex 95 SB
Brand: steute Pages: 10
Belkin OmniView Secure F1DN102Uea Quick Installation Manual preview
OmniView Secure F1DN102Uea
Brand: Belkin Pages: 36
N-Tron NT24k User Manual preview
NT24k
Brand: N-Tron Pages: 132
Imtex-Controls SLR Series Installation & Adjusting Instructions preview
SLR Series
Brand: Imtex-Controls Pages: 2
hager WXT30 Series Manual preview
WXT30 Series
Brand: hager Pages: 4
Icy Box IB-HUB1426-U3 Quick Installation Manual preview
IB-HUB1426-U3
Brand: Icy Box Pages: 10
hager HIB4 M Series Installation preview
HIB4 M Series
Brand: hager Pages: 3
Orei UHD-401MV User Manual preview
UHD-401MV
Brand: Orei Pages: 27
SIIG Hi-Speed USB 4-Port Bay Hub Quick Installation Manual preview
Hi-Speed USB 4-Port Bay Hub
Brand: SIIG Pages: 8
H3C WX3010E Installation Manual preview
WX3010E
Brand: H3C Pages: 70
IDT 89HPES12N3 User Manual preview
89HPES12N3
Brand: IDT Pages: 158

Brands by name

Popular brands

Load more brands