manualshive.com logo in svg

Dell S6100, Configuration Manual

The Dell S6100 Configuration Manual is a comprehensive guide that enables users to maximize the functionality of their Dell S6100 device. This manual can be easily downloaded for free from our website, allowing users to access valuable information and optimize their product experience.

Share
Download
background image

Oct 8 09:26:25: %RPM1:RP1 %BGP-5-ADJCHANGE: Connection with neighbor 1.1.14.2 

closed. Neighbor recycled

--More--

Example (History)

Dell#show logging history

Syslog History Table: 1 maximum table entries,

saving level Warnings or higher

  SNMP notifications not Enabled

%RPM:0:0 %CHMGR-2-LINECARDDOWN - Line card 3 down - IPC timeout

Dell#

show logging driverlog stack-unit

Display the driver log for the specified hardware component.

Syntax

show logging driverlog stack-unit 

stack-unit-number

Parameters

stack-unit 

stack-

unit-number

Enter the keywords 

stack-unit

 followed by the stack member ID of the switch for 

which you want to display the driver log.

defaults

none

Command Modes

•

EXEC

•

EXEC Privilege

Command History

This guide is platform-specific. For command information about other platforms, see the relevant 

Dell Networking 

OS Command Line Reference Guide

.

Version

Description

9.10(0.0)

Introduced on the S6100–ON.

9.8(1.0)

Introduced on the Z9100–ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Introduced on the S6000-ON.

9.2(1.0)

Introduced on the Z9500.

9.2(0.0)

Introduced on the M I/O Aggregator. This command is supported in Programmable-Mux 
(PMUX) mode only.

9.0.2.0

Introduced on the S6000.

8.3.19.0

Introduced on the S4820T.

8.3.11.1

Introduced on the Z9000.

8.3.7.0

Introduced on the S4810.

7.6.1.0

Introduced on the S-Series.

Example

Dell#show logging driverlog stack-unit 1

0:Task(tUsrRoot): [   491677]PSU FanCtrl Drv ERR: 

ssnDrvPoePsuEepromWriteEnable : 66 - Psu 1 is Not Present Cannot enable

1:Task(tUsrRoot): [      338]PSU FanCtrl Drv ERR: ssnDrvPsuFanCtrlInit : 118 - 

1538

Simple Network Management Protocol (SNMP) and Syslog

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for S6100

D-Link DKVM-IP1 Manual preview
DKVM-IP1
Brand: D-Link Pages: 73
Black Box SW1046A Manual preview
SW1046A
Brand: Black Box Pages: 28
I/O Interconnect SV142P1 User Manual preview
SV142P1
Brand: I/O Interconnect Pages: 27
DANLERS EZ CESR Installation Notes preview
EZ CESR
Brand: DANLERS Pages: 2
Cumberland PowerTrak Installation preview
PowerTrak
Brand: Cumberland Pages: 2
Metra Electronics CS-HDM3X1SW3 User Manual preview
CS-HDM3X1SW3
Brand: Metra Electronics Pages: 8
Lanpro SW2400S User Manual preview
SW2400S
Brand: Lanpro Pages: 16
J-Tech Digital JTD-2886 User Manual preview
JTD-2886
Brand: J-Tech Digital Pages: 81
Xantech HDMI3X1 User Manual preview
HDMI3X1
Brand: Xantech Pages: 5
InHand InSwitch ISM-P Series Web Config Manual preview
InSwitch ISM-P Series
Brand: InHand Pages: 81
Wyrestorm Essentials EXP-SW-0401-H2 Quick Start Manual preview
Essentials EXP-SW-0401-H2
Brand: Wyrestorm Pages: 2
Linksys SLM248G4PS Product Data preview
SLM248G4PS
Brand: Linksys Pages: 3
Micronor MR380 Series Instruction Manual preview
MR380 Series
Brand: Micronor Pages: 25
ABB OTM3200E4230C-GE Installation And Operating Instruction preview
OTM3200E4230C-GE
Brand: ABB Pages: 24
B&G NEMESIS Installation Manual preview
NEMESIS
Brand: B&G Pages: 11
Fujitsu Control 3-0801 User Manual preview
Control 3-0801
Brand: Fujitsu Pages: 374
Fujitsu FS-1008MT Series Specification Sheet preview
FS-1008MT Series
Brand: Fujitsu Pages: 5
CYP CP-290 Operation Manual preview
CP-290
Brand: CYP Pages: 8

Brands by name

Popular brands

Load more brands