Dell S6100 Configuration Manual Download Page 420

Page: 420 / 1743

•

EXEC Privilege

Command History

This guide is platform-specific. For command information about other platforms, see the relevant

Dell Networking

OS Command Line Reference Guide

Version

Description

9.10(0.0)

Introduced on the S6100-ON.

9.8(1.0)

Introduced on the Z9100–ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Added the ipv4 multicast and ipv6 unicast parameters.

9.4.(0.0)

Added support for VRF.

9.2(1.0)

Introduced on the Z9500.

9.0.2.0

Introduced on the S6000.

8.3.19.0

Introduced on the S4820T.

8.3.11.1

Introduced on the Z9000.

8.3.7.0

Introduced on the S4810.

7.8.1.0

Introduced on the S-Series.

7.7.1.0

Introduced on the C-Series.

Usage Information

To view the total number of COMMUNITY attributes found, use the

show ip bgp summary

command. The

text line above the route table states the number of COMMUNITY attributes found.

The

show ip bgp community

command without any parameters lists BGP routes with at least one BGP

community attribute and the output is the same as for the

show ip bgp

command output.

The following describes the

show ip bgp community

command shown in the following example.

Field

Description

Network

Displays the destination network prefix of each BGP route.

Next Hop

Displays the next hop address of the BGP router. If 0.0.0.0 is listed in this column, then
local routes exist in the routing table.

Metric

Displays the BGP route’s metric, if assigned.

LocPrf

Displays the BGP LOCAL_PREF attribute for the route.

Weight

Displays the route’s weight.

Path

Lists all the ASs the route passed through to reach the destination network.

Example

Dell# show ip bgp community ?

local-AS Do not export outside local AS (well-known community)

no-advertise Do not advertise to any peer (well-known community)

no-export Do not export to next AS (well-known community)

aa:nn Community number in aa:nn format

| Pipe through a command

Dell# show ip bgp community

BGP local RIB : Routes to be Added 0, Replaced 0, Withdrawn 0

BGP local router ID is 192.168.11.5

Status codes: s suppressed, S stale, d dampened, h history, * valid, > best

Path source: I - internal, a - aggregate, c - confed-external, r - redistributed

420

Border Gateway Protocol

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for S6100

Reviews:

Dell S6100, Configuration Manual, Page: 420 / 1743

Search results

Summary of Contents for S6100

Reviews: