manualshive.com logo in svg

Dell S6100, Configuration Manual, Page: 769 / 1743

Share
Download
Dell S6100 Configuration Manual Download Page 769

ipv6 icmp source-interface

Enable the ICMP error and unreachable messages to be sent with the source interface IP address, such as the loopback address, instead of 
the hops of the preceding devices along the network path to be used for easy debugging and diagnosis of network disconnections and 
reachability problems with IPv6 packets.

Syntax

ipv6 icmp source-interface 

interface 

Parameters

interface

Enter one of the following keywords and slot/port or number information:

•

For a Management Ethernet interface, enter the keyword 

managementethernet

.

NOTE: 

When you configure the capability to enable the loopback IP 

address to be sent for easy debugging and diagnosis (IP addresses of 

the devices for which the ICMP source interface is configured), the 

source IP address of the outgoing ICMP error message is modified,

 

although the packets are not sent out using the configured interface. 

Because the management interface is configurable only without any 

parameters such as the IP address, it is treated to the management 

interface of the primary unit or the existing unit.

•

For a 10-Gigabit Ethernet interface, enter the keyword 

TenGigabitEthernet

 then 

the stack/slot/port/subport information.

•

For a 25-Gigabit Ethernet interface, enter the keyword 

twentyFiveGigE

 then the 

stack/slot/port/subport information.

•

For a 40-Gigabit Ethernet interface, enter the keyword 

fortyGigE

 then the stack/

slot/port[/subport] information.

•

For a 50-Gigabit Ethernet interface, enter the keyword 

fiftyGigE

 then the stack/

slot/port/subport information.

•

For a 100-Gigabit Ethernet interface, enter the keyword 

hundredGigE

 then the 

stack/slot/port information.

•

For a Loopback interface, enter the keyword 

loopback

 then a number from 0 to 

16383.

•

For a port channel interface, enter the keywords 

port-channel

 then a number.

•

For a VLAN interface, enter the keyword 

vlan

 then a number from 1 to 4094.

Defaults

Not configured.

Command Modes

CONFIGURATION

Command History

This guide is platform-specific. For command information about other platforms, see the relevant 

Dell Networking 

OS Command Line Reference Guide

.

Version

Description

9.10(0.0)

Introduced on the S6100–ON.

9.8(1.0)

Introduced on the Z9100–ON.

9.8(0.0P5)

Introduced on the S4048-ON.

9.8(0.0P2)

Introduced on the S3048-ON.

9.7(0.0)

Introduced on the S6000-ON.

9.3(0.0)

Introduced on the S4810, S4820T, S6000, and Z9000 platforms.

IPv4 Routing

769

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments