manualshive.com logo in svg

Dell S6100, Configuration Manual, Page: 680 / 1743

Share
Download
Dell S6100 Configuration Manual Download Page 680

Version

Description

6.4.1.0

Introduced

Usage Information

You cannot delete the Null interface. The only configuration command possible in a Null interface is 

ip 

unreachables

.

Example

Dell(conf)# interface null 0

Dell(conf-if-nu-0)#

Related Commands

•

interface

 — configure a physical interface.

•

interface loopback

 — configure a Loopback interface.

•

interface port-channel

 — configure a port channel.

•

interface vlan

 — configure a VLAN.

•

ip unreachables

 — enable generation of internet control message protocol (ICMP) unreachable messages.

interface range

This command permits configuration of a range of interfaces to which subsequent commands are applied (bulk configuration). Using the 

interface range

 command, you can enter identical commands for a range of interface.

Syntax

interface range 

interface

 {[stack/]slot/port[/subport] | port} — {[stack/]slot/

port[/subport] | port}, 

interface

 {[stack/]slot/port[subport] | port} — 

{[stack/]slot/port[subport] | port},...

Parameters

interface 

{[stack/]slot/
port[subport] | 
port} — 
{[stack/]slot/
port[subport] | 
port}, 

interface 

{[stack/]slot/
port[subport] | 
port} — 
{[stack/]slot/
port[subport] | 
port},...

Enter 

interface range

 and one of the interfaces and then the interface information. 

Select the range of interfaces for bulk configuration. You can enter up to six comma-
separated ranges. Spaces are not required between the commas. The ranges can include 
VLANs, port-channels, and physical interfaces.

•

For a port channel interface, enter the keywords 

port-channel

 then a number.

•

For a 10-Gigabit Ethernet interface, enter the keyword 

TenGigabitEthernet

 then 

the stack/slot/port/subport information.

•

For a 25-Gigabit Ethernet interface, enter the keyword 

twentyFiveGigE

 then the 

stack/slot/port/subport information.

•

For a 40-Gigabit Ethernet interface, enter the keyword 

fortyGigE

 then the stack/

slot/port[/subport] information.

•

For a 50-Gigabit Ethernet interface, enter the keyword 

fiftyGigE

 then the stack/

slot/port/subport information.

•

For a 100-Gigabit Ethernet interface, enter the keyword 

hundredGigE

 then the 

stack/slot/port information.

•

For a VLAN interface, enter the keyword 

vlan

 then a number from 1 to 4094.

•

For a Tunnel interface, enter the keyword 

Tunnel

 then a number from 1 to 16383.

Defaults

None

Command Modes

CONFIGURATION

Command History

This guide is platform-specific. For command information about other platforms, see the relevant 

Dell Networking 

OS Command Line Reference Guide

.

680

Interfaces

Summary of Contents for S6100
















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments