Splicecom 4100 Скачать руководство пользователя страница 91

Страница: 91 / 374

Installation and Maintenance Manual

System Configuration

Installation and Maintenance Manual v4/0615/10

The Call Server field within the Phon

e or Trunk Module’s configuration form will display the name of the

Call Server that the module it is connected to, ie the name of the Secondary Call Server.

When connecting a Phone Module to a Secondary Call Server the additional Users created are all listed

under the Users list and have taken the next available extension numbers. Their Initial Phone field

displays which port on which Phone Module they are using and their Current Home field, which

determines which Call Server is providing their voicemail service, displays the name of the Secondary Call

Server.

Connecting a PCS IP phone to the Secondary Call Server

A PCS 58x/57x/56x, 55x, 542, PCS 410/400, PCS 100 can be connected to the Secondary Call Server as

described in the Connecting a PCS IP Phone from page 51. As well as a PCS 60 IP phone or PCS 50 IP

phone as described in the Installing User Software section from page 62.

The Initial P

hone field within the User’s configuration form will display which Call Server

/NSG the PCS is

connected to, ie the name of the Secondary Call Server. Please refer to page 95 for further details.

Select Phones and then the relevant Call Server/NSG to display which PCSs are connected to this Call

Server.

Connecting an existing Primary Call Server to another Primary Call Server

Where a Call Server has been previously working as a standalone system and is now to be connected to

another system the same method described above is used however the following should be noted:

Any configuration (other than the IP address and Call Server Name) previously stored on the

Secondary Call Server will be lost as this Call Server becomes a part

of the Primary Call Server’s system

and takes its configuration from the Primary Call Server.

Any Phone and/or Trunk modules and/or PCS IP phone should be disconnected from the Secondary

Call Server before it is connected to the Primary Call Server. They can be reconnected again as

described above.

A Global System

After the above procedures have taken place each Call Server, NSG, Phone Module, Trunk Module,

PCS 58x/57x/56x/55x, 410/400, 100, PCS 60 IP phone and PCS 50 IP phone is part of the one system

regardless of their location. The Primary Call Server will replicate the relevant configuration information to

each Secondary Call Server.

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды