Splicecom 4100 Скачать руководство пользователя страница 179

Страница: 179 / 374

Installation and Maintenance Manual

Configuring system functionality

Installation and Maintenance Manual v4/0615/10

175

In the Start Time field enter the time from which users can join the conference, eg 1100, with

no punctuation.

In the End Time field enter the time at which users can no longer join the conference, eg

1200, with no punctuation.

If the ability to initiate and join the conference is to be protected by a password, in the Pin field

enter a number which users must enter when starting or joining the conference.

If the conference is to be limited to a specific number of users, in the Maximum Members field

enter the maximum number of participants for this conference.

Select Update or Apply when ready.

Please note that if a Start and End Time are not specified it is advisable to use a PIN code so only

authorised users join the conference.

The conference is then initiated via a Dial Plan or DDI Call Plan entry as follows.

Initiating a Meet Me Conference

A Meet Me Conference can be started via a Dial Plan entry

similar to this example. Please note that Translate to field

can contain !CC or !ConferenceCreate.

After dialling the Dial Plan entry, eg *66, the user will be

asked to enter the conference number followed by #, eg

7987#. If a number has been entered in the Pin field for

this conference the user will be asked to enter the

conference PIN followed by #, eg 1234#. A beep will

confirm that the conference has been successfully started.

The following alternatives could be entered in the Translate To field:

!ConferenceCreate:<conference number> or !CC:<conference number>,

eg !ConferenceCreate:7987.

!ConferenceCreate:%r or !CC:%r

The User would dial the short code followed by the conference number and #, eg *997987#.

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды