manualshive.com logo in svg

Splicecom 4100, Инструкция по установке и обслуживанию

Kestrel 4100 - Компактный и точный прибор для измерения погодных условий. Получите бесплатное руководство по эксплуатации с инструкцией по быстрому старту. Скачать его с manualshive.com и начать использование сразу. Необходимый инструмент для путешественников и любителей спорта на открытом воздухе.

Поделиться
Скачать
background image

Installation and Maintenance Manual

 

 

 

Maintenance & Troubleshooting 

Installation and Maintenance Manual v4/0615/10 

 

293 

 

4

 

A hash (#) will appear, indicating that the previous entries where accepted and a command can be 

entered. 

5

 

Enter 

upgrade loader <IP address of Call Server>

    

eg upgrade loader 192.168.0.1 

6

 

When the hash (#) returns enter 

upgrade now 

or 

upgrade now <IP address of Call Server supplying the software>

, 

eg upgrade now 192.168.0.1 

7

 

The PCS will reboot and automatically restart. 

 

View the version of software via Telnet 
The version of software being run on the PCS 57x/56x/55x/542 can be viewed using Telnet as described 

above by entering: 

ver /mnt2/tpcs 

 

Upgrading a PCS 57x/56x/55x/542 on a remote site 
If the PCS 57x/56x/55x/542 to be upgraded is based at a satellite office, for example, and connected via a 

VPN, for example, and if, during the upgrade, this connection went down the phone would become 

inoperable.  The getupg command can be used instead to download the software to the phone first and 

then the upgrade will take place at the next reboot. 

 

1

 

Telnet on to the PCS 57x/56x/55x/542 as described above. 

2

 

Enter 

getupg <ip address of call server> admin <maintainer password>

 

eg getupg 192.168.0.1 admin password 

3

 

The software will be downloaded to the phone.   

4

 

When this process has finished the following will be displayed: 

Upgrade files have been saved.  Files will be installed at next reboot. 

5

 

Reboot the PCS 57x/56x/55x/542 at a convenient time and the phone will be upgraded. 

 

Upgrading the Software on the PCS 410/400 

Before starting the relevant software patch must be sent to the Call Server as described from page 286.  

You will require the following files: 

PCS 410 

–

 pcs410.tar.gz 

PCS 400 

–

 this is supplied with the software patch for the Call Server. 

 

Upgrading locally on the PCS 410 

1

 

On the PCS 410 lift the handset.  

2

 

Press the screen while rebooting the unit. 

3

 

As soon as the message 

“

Press screen to erase all, release for options

”

 appears 

let go of the screen 

4

 

The message “

Press screen before the bar completes to erase the config

”

 will 

appear.  Wait until the load bar is complete. 

5

 

The 

message “

Press screen before the bar completes to erase the code

”

 will 

appear. 

6

 

Press the screen 

7

 

When the message “

Code will be erased.  Please release screen to continue

“ 

appears let go of the screen 

8

 

The unit will be upgraded and the reboot will complete 

 

Содержание 4100























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4100

Advantech EKI-152X series User Manual preview
EKI-152X series
Бренд: Advantech Страницы: 94
TP-Link TL-PS110P Quick Installation Manual preview
TL-PS110P
Бренд: TP-Link Страницы: 16
IBM H SERIES RS/6000 Installation And Service Manual preview
H SERIES RS/6000
Бренд: IBM Страницы: 424
Simpact Freeway 1200 Hardware Installation Manual preview
Freeway 1200
Бренд: Simpact Страницы: 76
Advantech DVG-1100 Manual preview
DVG-1100
Бренд: Advantech Страницы: 43
Sun Microsystems Ultra Enterprise 3000 Installation Manual preview
Ultra Enterprise 3000
Бренд: Sun Microsystems Страницы: 48
QNAP TS-409 User Manual preview
TS-409
Бренд: QNAP Страницы: 203
Viavi G4-40G-010-384T Manual preview
G4-40G-010-384T
Бренд: Viavi Страницы: 12
Lantronix MPS1-2 Installation Manual preview
MPS1-2
Бренд: Lantronix Страницы: 100
ICP DAS USA tDS-700 Series Quick Start Manual preview
tDS-700 Series
Бренд: ICP DAS USA Страницы: 8
W&T 53641 Manual preview
53641
Бренд: W&T Страницы: 79
GIGA-BYTE TECHNOLOGY R182-P91 User Manual preview
R182-P91
Бренд: GIGA-BYTE TECHNOLOGY Страницы: 96
Planet ICS-2200T Quick Installation Manual preview
ICS-2200T
Бренд: Planet Страницы: 16
GRASS VALLEY K2 SOLO - Quick Start Manual preview
K2 SOLO -
Бренд: GRASS VALLEY Страницы: 108
Lantronix EDS3000PR Quick Start Manual preview
EDS3000PR
Бренд: Lantronix Страницы: 2
Oracle SPARC T5-4 Installation Manual preview
SPARC T5-4
Бренд: Oracle Страницы: 92
Dell EMC PowerEdge R740xd Installation And Service Manual preview
PowerEdge R740xd
Бренд: Dell EMC Страницы: 215
IBM TotalStorage FAStT700 User Manual preview
TotalStorage FAStT700
Бренд: IBM Страницы: 100

Бренды по названию

Популярные бренды

Загрузить еще бренды