Splicecom 4100 Скачать руководство пользователя страница 88

Страница: 88 / 374

Installation and Maintenance Manual

System Configuration

Installation and Maintenance Manual v4/0615/10

Connect the Call Server to the Primary Call Server either via the network or directly to a LAN

port on the Primary Call Server.

Power up the Call Server

Open Manager on the Secondary Call Server, eg http://192.16.0.252/manager

Within Manager Assist, select System Utilities

Under the Commands list select Ask Master

Within the Enter IP Address field enter the IP Address of the Primary Call Server, eg 192.168.0.1

Click on the Set Master button (ignore the system error message if displayed).

On the Primary Call Server:

In Manager select Unassigned Modules

Select the new Call Server, eg Secondary Call Server

From the Module Status list box select Member

Select Update or Apply when ready

Select Modules, select the Secondary Call Server, select the Call Server page and note that the

Administration Mode is set to Secondary.

The Secondary Call Server will now be a part of the system controlled by the Primary Call Server. The

Primary Call Server will replicate the relevant configuration information to the Secondary Call Server. This

means that the configuration of the system can be administered from either Call Server.

Linking two Call Servers across a WAN link

Ensure you are running the same version of software at both ends.

On the Primary Call Server:

This Call Server must be on different network to Secondary Call Server. Therefore, if necessary,

change the IP address of the Call Server, eg 194.168.0.1. If this Call Server is to act as the

DHCP Server change the DHCP properties, eg

Start Address = 194.168.0.2

End Address = 194.168.0.250

Base Address = 194.168.0.0

You may wish to give the Call Server a unique name to help identify this Call Server eg Primary

Call Server

Select the Call Server page and note the Administration Mode field is set to Primary.

A reboot will be required if any of the above settings are modified. Further details are available via

the Configuring a Call Server section from page 10.

On the Secondary Call Server:

Power up the Secondary Call Server

This Call Server must be on different network to Primary Call Server. Therefore, if necessary,

change the IP address of the Call Server, eg 192.168.1.1. If this Call Server is to act as the

DHCP Server change the DHCP properties, eg

Start Address = 192.168.1.2

End Address = 192.168.1.250

Base Address = 192.168.1.0

You may wish to the rename the Call Server to help identify this Call Server, eg Secondary Call

Server.

A reboot will be required if any of the above settings are modified. Further details are available

via the Configuring a Call Server section from page 10.
d

In Manager select WAN Links and select the Secondary Call Server

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды