Splicecom 4100 Скачать руководство пользователя страница 192

Страница: 192 / 374

Installation and Maintenance Manual

Configuring system functionality

188

Installation and Maintenance Manual v4/0615/10

Select Update

Select Update or Apply when ready.

Connect the relevant dongle to the relevant port and connect this to the device requiring ISDN

Please note:

No call progress tones are provided

When setting up Trunk ports to simulating ISDN into your system in a test environment the call can

go out on any port other than the NT port.

Trunk NT Mode Dongles

For technical data on NT mode dongles please refer to the maximiser Technical Reference manual.

Configuring DPNSS

A PRI port provided by a Call Server or Trunk Module can be configured to support DPNSS. No additional

licence is required for this feature other than a Trunk licence to enable a channel on the PRI port. This

implementation of DPNSS will support: Simple Calls, Name, Number, Loop Avoidance, Data Call, and

Node Numbers including Message Waiting and Visual Voice for Index.

Please refer to SpliceCom Support for assistance with configuration of DPNSS.

Creating a H.323 trunk

A Call Server can support H.323 Trunk services and can be configured as follows. Please note that the

required number of Trunk licences (one per channel) must be entered to use this facility (please refer to

page 20 for further details). When using a 4100 Call Server or 4140 Remote Call Server a Voice

Compression Module or card is required to use this facility across the Internet (please refer to page 36 for

further details).

In Manager select Modules

From the Module list select the Add H323 Gateway button

In the Name field enter a name to identify this external gateway

Enter the IP address of the remote end.

Select Apply

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды