Splicecom 4100 Скачать руководство пользователя страница 54

Страница: 54 / 374

Installation and Maintenance Manual

System Configuration

Installation and Maintenance Manual v4/0615/10

You will be prompted for the password for this Phone Module. By default this is

7388

. (The

Password is set within th

e relevant Phone Module’s configuration form.) Then press Enter.

Wait for a hash (#) to appear to confirm a connection has been made to the Phone Module

Enter

setnet

then press Enter

The current configuration will be displayed. You will be asked if you wish to change any of this

configuration.

Enter

then press Enter

Press Enter until the line “Audio Level” appears

Type in either

(recommended) or

depending on the volume level required.

Press Enter

You will be prompted to save this new configuration. Enter

The configuration will be saved.

Enter

poweroff

to reboot the phone module.

5100/5108 Call Server

To increase the volume output for the analogue ports on a Call Server a file called pots_level must be

created within the /SpliceCom directory as follows:

Telnet on to the Call Server as described in the Root Access to a Call Server section from page 272

Enter

vi /SpliceCom/pots_level

Press

to go to Insert mode

Type in either

(recommended) or

Press Esc to exit Insert mode

Enter

:wq

to quit the file and save the changes.

Reboot the Call Server

Connecting a PCS 520

When connecting a PCS 520 to an analogue port the following should be considered:

Caller Display Type

The Default Caller Display Type for an analogue port will be suitable for use with the PCS 520 however to

ensure that CLI information is displayed correctly and to allow the handset is to support Paging and Auto

Answer the System Phone Caller Display Type should be used. For details on how to configure an

Analogue Extension port please refer to page 89.

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды