manualshive.com logo in svg

Splicecom 4100, Инструкция по установке и обслуживанию

Kestrel 4100 - Компактный и точный прибор для измерения погодных условий. Получите бесплатное руководство по эксплуатации с инструкцией по быстрому старту. Скачать его с manualshive.com и начать использование сразу. Необходимый инструмент для путешественников и любителей спорта на открытом воздухе.

Поделиться
Скачать
background image

Installation and Maintenance Manual

 

 

 

 

 

Field Descriptions 

344 

 

Installation and Maintenance Manual v4/0615/10 

 

 

Serial Number 

The primary MAC address of this module. 

 

IP Address 

IP Address of this module, in xxx.xxx.xxx.xxx form. 

 

Product Version 

Software version running on this module 

 

Module Status 

Member  

A module that is a part of the system 

Available  

A module that is waiting for permission to join 

NonMember  

Non members are modules that are part of another system, but because of the 

network are visible for this domain.  This mode prevents them joining the wrong 

domain. 

 

Flash LED 

The Flash LED button will instruct the Call Server’s SpliceCom LED to flash 20 times.

 

 

Call Server/Remote Call Server page 

Administration Mode 

Primary  

A Call Server that is the master administrative module controlling the configuration 

database. 

Secondary  

A Call Server that is linked to a Primary Call Server and receives its configuration from the 

Primary. 

 

DHCP Server Mode 

Enable  

The Call Server will act as the DHCP server using the IP Address range specified in the DHCP 

Start Address and DHCP End Address fields.  If another DHCP Server has been detected on 

the network and the Call Server is rebooted it will keep its previous IP address and disable 

its own DHCP server. 

Disable  

DHCP is disabled; the Call Server will use the IP address entered in the IP Address field 

within the General page. 

Client  

The Call Server will act as the DHCP client obtaining an IP address from a DHCP Server on 

the network. 

 

DHCP Start Address 

First IP address of the IP address range to be used when the DHCP Server Mode is set to Enable.  Default 

= 192.168.0.2.  (Please note that this field is irrelevant if the DHCP Server Mode is set to Disabled.) 

 

DHCP End Address 

Last IP address of the IP address range to be used when the DHCP Server Mode is set to Enable.  Default 

= 192.168.0.250.  The system assumes a linear distance between the two numbers and has no knowledge 

of sub address masks.  (Please note that this field is irrelevant if the DHCP Server Mode is set to Disabled.) 

 

DHCP Base Address 

Default = 192.168.0.0.  The network on which the Call Server will be allocating IP addresses.  If DHCP is 

disabled this must be configured to match the network that the Call Server is on. 

 

Содержание 4100























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4100

IBM BladeCenter S Installation And User Manual preview
BladeCenter S
Бренд: IBM Страницы: 84
IBM 9008-22L Manual preview
9008-22L
Бренд: IBM Страницы: 110
LaCie 2big Network 2 Datasheet preview
2big Network 2
Бренд: LaCie Страницы: 4
IBM xSeries 235 Maintenance & Troubleshooting preview
xSeries 235
Бренд: IBM Страницы: 214
Patton electronics 29XX Series Administrator'S Reference Manual preview
29XX Series
Бренд: Patton electronics Страницы: 326
3Com 3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print... User Manual preview
3CRWPS10075-US - OfficeConnect Wireless 54Mbps 11g Print...
Бренд: 3Com Страницы: 94
Nortel 297-2183-912 Installation Manual preview
297-2183-912
Бренд: Nortel Страницы: 144
QNAP TS-h 90FU Series User Manual preview
TS-h 90FU Series
Бренд: QNAP Страницы: 75
Zonet ZUH2000 - Product Data preview
ZUH2000 -
Бренд: Zonet Страницы: 2
BITMAIN ANTMINER S19 Pro+ Hydro Installation Manual preview
ANTMINER S19 Pro+ Hydro
Бренд: BITMAIN Страницы: 17
ICP DAS USA PDS-8 1 Series Manual preview
PDS-8 1 Series
Бренд: ICP DAS USA Страницы: 9
Intel SE7520AF User Manual preview
SE7520AF
Бренд: Intel Страницы: 64
Intel SE7501CW2 Product Manual preview
SE7501CW2
Бренд: Intel Страницы: 93
Mackie MDR 24/96 Technical Reference preview
MDR 24/96
Бренд: Mackie Страницы: 110
TROY Group TROY200 Series Installation And User Manual preview
TROY200 Series
Бренд: TROY Group Страницы: 34
Inspur NF5280M6 Installation Manual preview
NF5280M6
Бренд: Inspur Страницы: 4
Bay Networks Remote Annex 4000 Hardware Installation Manual preview
Remote Annex 4000
Бренд: Bay Networks Страницы: 162
Gateway ALR 8200R User Manual preview
ALR 8200R
Бренд: Gateway Страницы: 150

Бренды по названию

Популярные бренды

Загрузить еще бренды