Splicecom 4100 Скачать руководство пользователя страница 349

Страница: 349 / 374

Installation and Maintenance Manual

Field Descriptions

Installation and Maintenance Manual v4/0615/10

345

DHCP Base Mask

Default = 255.255.255.0. The subnet mask to be used by the Call Server, and if the DHCP Server mode is

set to Enable, this will be the subnet mask given out. If DHCP is disabled this must be configured to

match the network that the Call Server is on.

DHCP Router

The IP address of the default gateway to be used by the Call Server, and if the DHCP Server mode is set to

enable, this will be the Default Gateway IP address given out.

DNS Domain

Domain name

DNS Primary

DNS primary server

DNS Secondary

DNS secondary server

SMTP Server Address

The IP address of the mail server to receive the Warnings and Notifications emails for this Call Server.

Email Source Address

The address that emails will appear to come from.

Email Source Name

The name that goes in front of the email address.

SMTP Domain Name

If required for SMTP server authentication

SMTP Username

User name for SMTP server authentication

SMTP Password

Password for SMTP server authentication

Email address for Warnings

The email address to be sent a message when an entry is made in the Warnings page.

Email address for Notifications

The email address to be sent a message when a notification is made, eg when the Call Server needs to

perform an “Ask Master”.

Public (Internet) IP Address

The public/external IP address for the module. For use with multiple Call Servers using a public network

through NAT routers.

Auto Add Phones

Enable / Disable. If enable, this feature will allow Phone Modules and IP Phones to automatically register

with the Call Server. If disabled Phone Modules and IP Phones must be manually registered.

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды