Splicecom 4100 Скачать руководство пользователя страница 85

Страница: 85 / 374

Installation and Maintenance Manual

System Configuration

Installation and Maintenance Manual v4/0615/10

Installing the SSL Gateway on a Linux PC

Initial consideration

SSL Gateway must be in installed on PC running OpenSUSE 12.3

Minimum hardware requirement - 1 Gbps processor, 2 GB memory

SSL Gateway software is 32 bit so will run on 32 or 64 bit Linux (64 bit is recommended if a choice is

available)

Can reside on the same PC as S8000 and/or Vision (except Vision Call Centre)

Linux configuration:

The IP address of the SSL Gateway is the IP address of the Linux PC. This IP address must be

associated with eth0.

DHCP, IP routing, DNS, NFS Server and NTP services are all configured within Linux

The Linux PC must have a User

called “splicecom”

. It is recommended that Auto Login is turned

off for this User account.

You will need to know the root password to enter and execute Terminal commands during

installation and configuration.

Ensure that the Firewall available on the Linux PC is turned off

Enable Remote Administration (VNC)

Enable the sshd service

Ensure that Linux PC does not hibernate or shut down

During the installation the Linux PC must be connected to the Internet or have access to the Linux

installation CD

Installing the software

Copy the SSL Gateway software onto the Linux PC

Via Terminal go to the directory where the software is stored

Enter the following command to extract the software

tar

–

xf SSL-Gateway-Linux.tar.gz

This will create a new directory called SSL-Gateway

Change to this directory, eg cd SSL-Gateway

Enter

sudo ./install.SUSE

(use this command if you are using the Linux installation CD)

Enter

sudo ./install.SUSE - net

(use this command if the installation files are to be retrieved via the Internet, preferred method)

Once the Installation complete message is displayed and the prompt has returned the following

commands will configure the Linux PC to communicate with the Call Server

Enter

sudo vi /etc/xinetd.d/upcs

Once the xinetd file is displayed, press i to go into Insert Mode

Change the server_args line to read

–

securepartner

–

gk ip address of call server

Ensure the Port line is set to 5000

Press ESC to exit Insert Mode

Enter :wq to save any changes

You will be returned to Terminal prompt

Enter the following command to restart xinetd and apply the changes

sudo /sbin/service xinetd restart

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды