Splicecom 4100 Скачать руководство пользователя страница 215

Страница: 215 / 374

Installation and Maintenance Manual

Working with Voicemail

Installation and Maintenance Manual v4/0615/10

211

As such, all these tasks will dynamically consume Voicemail Port channels. Please take this into account

when planning capacity for your requirements.

Please refer the Reseller area of the SpliceCom website for installation instructions.

Voicemail Licensing

VoicemailPort licence

Each S8002, S716, NSG and 5108 are supplied with 2 simultaneous connections to voicemail, and the

5100 Call Server is supplied with 4 simultaneous connections. This capacity can be expanded via the

purchase and installation of VoicemailPort licences (the S8000 can support up to 250 connections, the

S716 up to 15, the 5100 up to 16, and the 5500 NSG and 5108 can support up to 8 connections). One

licence per port/channel.

Once additional VoicemailPort licences have been installed the additional number of channels must be

entered within Capacity field of the relevant VoicemailPort.

This licence will also facilitate the use of the Voice Processing application run on a standalone Linux PC or

server.

MessageBox licence

Each User and Department on the system can be configured to use the voicemail functionality. To

activate this use a MessageBox licence must be purchased, installed and assigned to the User or

Department.

When purchasing a Call Server or soft PBX licence the following number of MessageBox licences are

provided:

S8004 licence will be provided with 2 MessageBox licences

S716 licence will be provided with 2 MessageBox licences

A 5100 Call Server will be provided with 10 MessageBox licences

A 5108 Call Server will be provided with 5 MessageBox licences

5500 NSG will be provided with 2 MessageBox licences

A 4100 Call Server will be provided with 30 MessageBox licences,

A 4140 Remote Call Server is provided with 10 MessageBox licences.

Additional MessageBox licences can be purchased up to a maximum of 1,200 on a S8000, 20 on a S716,

600 on a 5100, 300 on a NSG and 20 on 5108 Call Server.

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды