manualshive.com logo in svg

Splicecom 4100, Инструкция по установке и обслуживанию

Kestrel 4100 - Компактный и точный прибор для измерения погодных условий. Получите бесплатное руководство по эксплуатации с инструкцией по быстрому старту. Скачать его с manualshive.com и начать использование сразу. Необходимый инструмент для путешественников и любителей спорта на открытом воздухе.

Поделиться
Скачать
background image

Installation and Maintenance Manual

 

 

 

 

 

System Configuration 

62 

 

Installation and Maintenance Manual v4/0615/10 

 

Connect to the Call Server remotely 

If the PCS 410/400/100 is to be installed at a remote location, eg via a VPN connection, the phone should 

be configured with the IP address of the Call Server it is to connect to as follows. 

1

 

Follow steps 1-7 as described above to telnet on to the phone and access Setnet. 

2

 

Press Enter until the line “Startup arguments” appears.

 

3

 

Type in 

–

gk <ip address of call server>

 eg 

–

gk 192.168.0.1, and press Enter 

4

 

Continue to press Enter until you are asked if you wish to save the changes.  Enter 

y

. 

5

 

Telnet will display that the changes have been saved. 

6

 

When finished enter 

poweroff

 and the PCS will reboot. 

 

If the Call Server is to collect BLF data from this remote phone enter 

–

blf

 after the IP address of the call 

server, eg 

–

gk 192.168.0.1 

–

blf.  The Call Server will then multicast this BLF information to all PCSs on the 

system. 

 

If there are more than one remote IP Phone connected to the system one of these phones can be 

configured to collect the BLF data from all the remote phones and send this to the system.  This can be 

achieved by entering 

–

relay

 after the IP address, eg 

–

gk 192.168.0.1 

–

relay.  The other phones would 

then just be configured with the IP address of the call server, eg 

–

gk 192.168.0.1. 

 

It is recommended that no more than 5-6 remote IP phones should be configured to use this facility in 

order to keep the overhead on the Call Server to a minimum. 

 

To remove this entry repeat steps 1 and 2 above.  Delete the entry within Startup arguments and press 

Enter.  Continue with steps 4, 5 and 6 above. 

Installing User Software 

Navigate 

Navigate is a PC application that provides standard telephony functionality, CLI display and gives Users 

the ability to set features such as forwarding and DND via an easy to use dialogue box or Quick Settings 

bar.   It can be run on MS Windows 7 or above.  It can be installed as an IP soft phone on a multi-media 

PC or programmed to partner a User’s telephone handset (PCS 58x, 57x, 56x, 

55x, 542, 410/400, 100, 520, 

10, 505, 5 or an alternative analogue handset).  

 

Please refer to the Navigate User Manual for detailed descriptions on how to use this software. 

 

Содержание 4100























































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 4100

Aastra 400 Series System Manual preview
400 Series
Бренд: Aastra Страницы: 592
Logicbus PDS Series Quick Start Manual preview
PDS Series
Бренд: Logicbus Страницы: 8
Supermicro SuperServer 5039MD18-H8TNR User Manual preview
SuperServer 5039MD18-H8TNR
Бренд: Supermicro Страницы: 134
7thSense M101-4 User Manual preview
M101-4
Бренд: 7thSense Страницы: 28
Intergraph InterServe 600 Series System Reference Manual preview
InterServe 600 Series
Бренд: Intergraph Страницы: 104
Sun Microsystems Sun Fire Netra 1280 Product Notes preview
Sun Fire Netra 1280
Бренд: Sun Microsystems Страницы: 10
Lantronix Device Installer User Manual preview
Device Installer
Бренд: Lantronix Страницы: 21
Lantronix Device Server MSS 485 Installation Manual preview
Device Server MSS 485
Бренд: Lantronix Страницы: 69
Lanner ISD-V330 User Manual preview
ISD-V330
Бренд: Lanner Страницы: 72
Zte ZXCLOUD R5300 G3 Maintenance Manual preview
ZXCLOUD R5300 G3
Бренд: Zte Страницы: 19
G-Technology G-RAID Studio Product Manual preview
G-RAID Studio
Бренд: G-Technology Страницы: 50
Pepperl+Fuchs BTC12N Series Manual preview
BTC12N Series
Бренд: Pepperl+Fuchs Страницы: 45
B+B SmartWorx VESP211 Quick Start Manual preview
VESP211
Бренд: B+B SmartWorx Страницы: 2
Micron NetFRAME 2100 Series Product Manual preview
NetFRAME 2100 Series
Бренд: Micron Страницы: 178
Supero 7042M-6 User Manual preview
7042M-6
Бренд: Supero Страницы: 106
Supero 6016T-6RFT User Manual preview
6016T-6RFT
Бренд: Supero Страницы: 108
Intel SE7520AF2 Technical Product Specification preview
SE7520AF2
Бренд: Intel Страницы: 256
TROY XCD MAN-EXT2000 Administrator'S Manual preview
MAN-EXT2000
Бренд: TROY XCD Страницы: 252

Бренды по названию

Популярные бренды

Загрузить еще бренды