Splicecom 4100 Скачать руководство пользователя страница 324

Страница: 324 / 374

Installation and Maintenance Manual

Field Descriptions

320

Installation and Maintenance Manual v4/0615/10

Deliver and Delete Used in conjunction with the Email or ArchiveEmail Contact Type. A new

voicemail message will be automatically sent to the email address entered in the

Telephone Number field. The message will be immediately deleted from the

voicemail server.

Deliver New

Used in conjunction with the Telephone Contact Type. Voicemail will attempt to

deliver a new voicemail message to the number entered in the Telephone

Number field however the message will not be preceded by the usual statement

indicating the number of new messages received.

Deliver Link

Used in conjunction with the Email Contact Type. A new voicemail message will

be automatically sent to the email address entered in the Telephone Number field

and linked to the embedded media player on the recipient’s PC.

Licences page

Messagebox Licence

Enable/Disable. Assigns a MessageBox licence to this Department. Required to activate voicemail for this

Department.

Groups

Name

64 Domain Characters. Name of the Group.

Description

128 Characters. Text description of the Group.

Company

The name (GUID) of the Company to which this Group has been assigned.

Order

The order in which calls will be presented to the Members. The member with the higher number will be

presented with a call first, then the next highest and so on.

Member

The list of Users, Phones and/or Groups that are members of this Group.

Capability

16 characters. Name of the capability. Proceed the name with an underscore (_) if being configured for

Group Log in/out or this Group is to be populated by Vision Call Centre Agents, and match the name

entered in the User’s Capability field.

Capability Percent

Percentage 1-100. Minimum strength of this capability. If Group Log in/out is being configured or this

Group is to be populated by Vision Call Centre Agents enter a number the same or lower than the

number entered in the User’s Capability Percent field.

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Похожие инструкции для 4100

Бренды по названию

Популярные бренды