Splicecom 4100 Скачать руководство пользователя страница 312

Страница: 312 / 374

Installation and Maintenance Manual

Field Descriptions

308

Installation and Maintenance Manual v4/0615/10

Out Of Office Message

64 Characters. Additional text that will be displayed with the message selected above; eg until

29 September, in Boardroom, etc.

Do Not Disturb

Enable/Disable. When enabled the User will not receive any calls and the extension is considered busy

unless the incoming number matches an entry in the DND Exceptions list.

Exception Telephone Number

List of telephone numbers that will get through even when Do Not Disturb is set. With Left hand partial

matching.

Capability page

Capability

16 Characters. Name of capability, eg French. Proceed the name with an underscore (_) if being

configured for Group Log in/out or this User is to become a Vision Call Centre Agent, and match the

name entered in the Group’s Capability field

Capability %

Percentage 1-100. Strength of this capability, eg 50%. If Group Log in/out is being configured or this

User is to become a Vision Call Centre Agent enter a number the same or higher than the number

entered in the Group’s Capability Percent field.

Tunes page

Telephone Number

Used in conjunction with the CallerID and Destination Ring Tune Type. Determines for which number the

ring tune will be used.

Ring Type

The instance when the selected tune is used

System

ANY system call (Telephone Number field is ignored)

Internal

ANY internal number (Telephone Number field is ignored)

External

ANY external number (Telephone Number field is ignored)

CallerID

Left hand matches the incoming Caller ID. (This has priority over all other entries).

Destination

Left hand matches the destination number of the call. (This has priority over Internal or

External entries).

Parallel

Used in conjunction with Forward/Follow Me Both Personal feature. Determines the

ring tune to be played on the User’s extension. (Telephone Number field is ignored)

Ring Tune

The Ring Tune/ringing method to be used.

Speed Dial page

Telephone Number

64 Digits. Telephone number to be dialled when this speed dial is selected.

Содержание 4100























































































































































































































































































































































































Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды

Splicecom 4100, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 4100

Отзывы:

Бренды по названию

Популярные бренды