Valco Cincinnati VC350A Manual Download Page 75

Page: 75 / 327

Section 10

—

Troubleshooting

VC350A Flexoseal

System

Valco Cincinnati

10-5

Problem

Possible Cause

Possible Solution

Glue Pattern, continued

22. Glue is not present on

product.

22a.

Glue pressure is too high (the air
required to operate the valve
cannot overcome the glue
pressure.)

22b. Not enough air pressure at the

glue pump

22c.

Obstruction in glue supply line
or pressure regulator

22d. Low glue supply or no glue

22e.

Defective pump

22f.

Filters are clogged

22g. Control has not been turned on

22h. Defective power switch

22i.

Defective control fuse

22j.

Defective valve circuit fuse

22k. Damaged valve cable

22l.

Loose cable connections

22m. Valve selector switch (front

panel of control) is in the wrong
position.

22n. Dirty or defective fluid pressure

regulator

22o. Defective solenoid air valve

22p. Obstruction in the glue valve

22q. Obstruction in the applicator

head

22a. Decrease the glue pressure.

22b. Increase air pressure and check

the air supply.

22c. Clean the glue supply

22d. Replenish the glue

22e. Repair or replace pump

22f.

Clean the filters

22g. Turn on control.

22h. Replace power switch/module.

22i.

Replace control fuse.

22j.

Replace valve circuit fuse.

22k. Replace cable.

22l.

Tighten cable connections.

22m. Set switch to proper position.

22n. Clean or replace the regulator.

22o. Repair or replace the solenoid

air valve.

22p. Clean or repair the glue valve.

22q. Remove the applicator head

and flush with water. Remove
the side screws and flush with
water.

23. Intermittent glue

pattern.

23a.

Air is present in the glue lines

23b. Loose air solenoid valve

connection

23c.

Applicator head does not touch
the product

23d. Incorrect angle of applicator

head

23a. Purge air from the glue lines.

23b. Tighten connection.

23c. Adjust tension spring.

23d. Adjust head angle to 35°.

24. Too much glue on

one side of pattern.

24a.

Applicator assembly is either too
high or too low

24a. Adjust head angle to 35°.

Summary of Contents for VC350A








































































































































































































































































































































Search results

Summary of Contents for VC350A

Reviews:

Related manuals for VC350A

Brands by name

Popular brands

Valco Cincinnati VC350A, Manual

Search results

Summary of Contents for VC350A

Reviews:

Related manuals for VC350A

Brands by name

Popular brands