Valco Cincinnati VC350A Manual Download Page 228 | Manualshive

Page: 228 / 327

background image

5-2

Valco Cincinnati, Inc.

Section 5 - Basic Features

MC060 Manual/VC350AG AutoGlue Control System

Item #

Name

Description

1

Start switches (start of pattern)

Used to set the start point of the glue pattern. Values can
be entered up to 99.99 inches for imperial systems (9999
millimeters for metric systems).

2

Stop switches (end of pattern)

Used to set the point at which the glue pattern will end.
Values can be entered up to 99.99 inches for imperial

(9999 millimeters for metric systems). In AutoGlue, this is
the dimension at which the glue stops before the end of

the tab.

3

Sensor LED

When illuminated, this LED indicates that the scanner
has seen the product. This will illuminate while the

scanner is activated.

4

“Glue enable” LED

When illuminated, this LED indicates the glue-enable
signal is present to the valve-driver board to turn on the

glue valve.

Note! The LED will illuminate below minimum speed,

even though there is no glue being applied.

5 Fluid-flow-control

adjustment

knob

Allows for fine adjustment of glue volume. Changes can
be seen on the front-panel pressure gauge.

6

Valve –selector switch

Allows for the selection of valve. When the switch is off,
the valve does not fire, even though the glue-enable LED
is flashing. The gun switch must be on in order to apply
glue when the glue-enable LED is flashing. (See Note

below)

7

Fluid-flow-control pressure gauge

Indicates a boost in air pressure added to the preset
pressure of glue regulator. Can be adjusted using fluid-

flow-control adjustment knob.

8

“Power-on” LED

When illuminated, this LED indicates the power is on.

9

AutoGlue Selector Switch

Selects either AutoGlue mode (up) or Pattern Glue mode
(down) of operation.

10

AutoGlue LED

When illuminated, the control is in AutoGlue mode and
will glue the entire tab minus start and stop dimensions.

11

Pattern Glue LED

When illuminated, the control is in Pattern Glue mode
and will start at first dimension and stop at end
dimension.

Front Panel Features - Continued

Table 5-1. VC350AG Front-Panel Features

Setting all of the front panel start and
stop switches to “0000 0000” will NOT
disable the glue valve. The valve-
selector On/Off switch is used to turn off
or “disable” the valve.

«
...
226
227
228
229
230
...
»

Summary of Contents for VC350A








































































































































































































































































































































Reviews:

No comments

Related manuals for VC350A

Brand: THORLABS Pages: 44

Brand: ACE INSTRUMENTS Pages: 2

Brand: ODA Pages: 103

Brand: vanEE Pages: 52

Brand: Caddon Hives Pages: 3

Brand: M-system Pages: 2

Brand: Rico Pages: 34

Brand: Idex Pages: 141

Brand: IDEAL Networks Pages: 8

Brand: IDEAL Networks Pages: 5

Life/form SmartScope LF01142U

Brand: Nasco Pages: 2

Brand: Taylor Pages: 41

Brand: neofeu Pages: 28

Brand: Crosley Pages: 6

Brand: Gambro Pages: 273

Brand: Meritor Pages: 65

KONTROL KUBE ABACUS

Brand: FIBERLOCK Pages: 8

Brand: Monosem Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands