Valco Cincinnati VC350A Manual Download Page 222 | Manualshive

Page: 222 / 327

background image

2-3

Valco Cincinnati, Inc.

MC060 Manual/VC350AG AutoGlue Control System

Section 2 - Safety Information

Cautions

All personnel involved with the installation, operation, and maintenance of the
equipment must read and thoroughly understand the following cautions:

CAUTION!

CAUTION!

CAUTION!

CAUTION!

CAUTION! Never hose or steam-clean the unit. If the surrounding

area is cleaned in this manner, protect the unit by
covering it with plastic or other waterproof material.
OTHERWISE, DAMAGE TO EQUIPMENT COULD
OCCUR.

CAUTION!

CAUTION!

CAUTION!

CAUTION!

CAUTION! Do not bend hot-melt hoses less than an 18-inch (460

mm) radius. OTHERWISE, EQUIPMENT DAMAGE
COULD OCCUR.

CAUTION!

CAUTION!

CAUTION!

CAUTION!

CAUTION! Place Material Safety Data Sheets for the adhesive

near the unit. OTHERWISE, DAMAGE TO EQUIPMENT
COULD OCCUR.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING! The heat that is contained in hot-melt material will

continue to penetrate and deeply burn the skin unless
rapidly cooled by external means such as water. Do not
attempt to remove set hot-melt adhesive from the skin.
OTHERWISE, PERSONAL INJURY COULD OCCUR.

If hot adhesive comes in contact with the skin,

, ,

, , do the following:

1.

Immediately immerse the contacted area in clean, cold water.

It is recommended that a source of
clean, cold water be provided near the
hot-melt work area.

2.

Cover the affected area with a clean, wet compress and see a
physician immediately.

During the heating and melting process, the surface of the adhesive will be
exposed to air. The mixture of polymer fumes and air can catch fire if the hot-
melt is overheated.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING! Poor ventilation, smoking, and open flames can cause

overheated hot-melt to ignite. Adequate ventilation
must be provided. Smoking should be prohibited in the
immediate vicinity of the molten adhesive. Open flames
must be kept away from the area around molten
adhesive. OTHERWISE, DEATH, PERSONAL INJURY,
OR DAMAGE TO EQUIPMENT COULD OCCUR.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING! Exposed arcing may ignite the fume/air mixture. Shield

all electrical equipment from melt fumes to avoid
exposed arcing. OTHERWISE, PERSONAL INJURY
OR EQUIPMENT DAMAGE COULD OCCUR.

What to Do if Contact

with Hot Adhesive

Occurs

What to Do if

Adhesive-Related Fire

or Explosion Occurs

«
...
220
221
222
223
224
...
»

Summary of Contents for VC350A








































































































































































































































































































































Reviews:

No comments

Related manuals for VC350A

Brand: XTA Pages: 29

Brand: vc999 Pages: 59

Brand: Qtx Pages: 3

Brand: Saferoad Pages: 24

Brand: Datavideo Pages: 48

Brand: Datavideo Pages: 34

Brand: Datavideo Pages: 3

Brand: Datavideo Pages: 34

Brand: Datavideo Pages: 8

Brand: Datavideo Pages: 10

Brand: fadini Pages: 20

Brand: Easylife Pages: 3

Brand: York Pages: 32

Carestation 620

Brand: GE Pages: 268

Brand: GE Pages: 50

Brand: Vibration Research Corporation Pages: 333

accumet BASIC AB 15

Brand: Fisher Scientific Pages: 56

Brand: Lievers Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands