Valco Cincinnati VC350A Manual Download Page 10 | Manualshive

Page: 10 / 327

background image

Section 2

—

Safety Information

VC350A Flexoseal

®

System

Valco Cincinnati

2-2

WARNING! When making adjustments or performing checkout procedures,
stay clear of any moving mechanical parts and do not touch exposed electri-
cal equipment or electrical connectors. OTHERWISE, DEATH OR PERSONAL
INJURY COULD OCCUR.

WARNING! Keep pump cover and electrical enclosures closed except during
setup, service, and checkout procedures. OTHERWISE, DEATH OR PER-
SONAL INJURY COULD OCCUR.

WARNING! Promptly repair or replace all worn or damaged parts. OTHER-
WISE, PERSONAL INJURY OR EQUIPMENT DAMAGE COULD OCCUR.

WARNING! Always wear insulated gloves and proper eye protection when
working around hot-melt equipment. A protective screen around the face is
also recommended. OTHERWISE, DEATH OR PERSONAL INJURY COULD
OCCUR.

WARNING! Purge the fluid pressure from the system before disconnecting
any part of the system. OTHERWISE, DEATH OR PERSONAL INJURY COULD
OCCUR.

WARNING! People with respiratory problems (e.g., asthma, bronchitis, etc.)
should not work in the vicinity of molten adhesive. RESPIRATORY PROB-
LEMS MAY BE AGGRAVATED BY THE FUMES. Do not wear a face mask
when working around molten adhesive. THE MASK MAY TRAP THE FUMES
AND DEATH OR PERSONAL INJURY COULD OCCUR.

WARNING! Keep hot-melt hoses away from walkways and the moving parts
of hot-melt systems. OTHERWISE, PERSONAL INJURY OR EQUIPMENT
DAMAGE COULD OCCUR.

WARNING! The hot-melt unit should be installed so that it can be turned off at
a location away from the hot-melt unit. OTHERWISE, DEATH, PERSONAL
INJURY, OR EQUIPMENT DAMAGE COULD OCCUR.

Cautions

All personnel involved with the installation, operation, and maintenance of the equipment must read and thoroughly
understand the following cautions:

CAUTION! Never hose or steam-clean the unit. If the surrounding area is
cleaned in this manner, protect the unit by covering it with plastic or other
waterproof material. OTHERWISE, DAMAGE TO EQUIPMENT COULD OCCUR.

CAUTION! Do not bend hot-melt hoses less than an 18-inch (460 mm) radius.
OTHERWISE, EQUIPMENT DAMAGE COULD OCCUR.

CAUTION! Place Material Safety Data Sheets for the adhesive near the unit.
OTHERWISE, DAMAGE TO EQUIPMENT COULD OCCUR.

«
...
8
9
10
11
12
...
»

Summary of Contents for VC350A








































































































































































































































































































































Reviews:

No comments

Related manuals for VC350A

Brand: Navman Pages: 17

Brand: Laica Pages: 4

Brand: Nautilus Pages: 12

Brand: CAIRE Pages: 16

Brand: Garmin Pages: 12

Brand: Garmin Pages: 13

ENET-232 Series

Brand: National Instruments Pages: 105

Brand: National Instruments Pages: 22

RIDA qLine ZG2601

Brand: R-Biopharm Pages: 23

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Brand: M-Audio Pages: 25

Brand: Össur Pages: 98

Flex Foot Cheetah

Brand: Össur Pages: 107

Brand: Össur Pages: 38

Brand: Össur Pages: 39

Bionic Symbionic Leg

Brand: Össur Pages: 2

Brand: Össur Pages: 67

Brand: Össur Pages: 17

Brand: mychway Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands