Valco Cincinnati VC350A Manual Download Page 11 | Manualshive

Page: 11 / 327

background image

Section 2

—

Safety Information

VC350A Flexoseal

®

System

Valco Cincinnati

2-3

What to Do if Contact with Hot Adhesive Occurs

WARNING! The heat that is contained in hot-melt material will continue to
penetrate and deeply burn the skin unless rapidly cooled by external means
such as water. Do not attempt to remove set hot-melt adhesive from the skin.
OTHERWISE, PERSONAL INJURY COULD OCCUR.

If hot adhesive comes in contact with the skin

,

do the following:

1. Immediately immerse the contacted area in clean, cold water.

Note!

It is recommended that a source of clean, cold water be provided near the hot-melt
work area.

2. Cover the affected area with a clean, wet compress and see a physician immediately.

What to Do if Adhesive-Related Fire or Explosion Occurs

During the heating and melting process, the surface of the adhesive will be exposed to air. The mixture of polymer
fumes and air can catch fire if the hot-melt is overheated.

WARNING! Poor ventilation, smoking, and open flames can cause overheated
hot-melt to ignite. Adequate ventilation must be provided. Smoking should
be prohibited in the immediate vicinity of the molten adhesive. Open flames
must be kept away from the area around molten adhesive. OTHERWISE,
DEATH, PERSONAL INJURY, OR DAMAGE TO EQUIPMENT COULD OCCUR.

WARNING! Exposed arcing may ignite the fume/air mixture. Shield all electri-
cal equipment from melt fumes to avoid exposed arcing. OTHERWISE, PER-
SONAL INJURY OR EQUIPMENT DAMAGE COULD OCCUR.

WARNING! Do not use a water extinguisher to extinguish the fire! OTHER-
WISE, PERSONAL INJURY OR EQUIPMENT DAMAGE COULD OCCUR.

If the hot-melt adhesive ignites, promptly perform the following steps:

1. Sound a fire alarm.

2. Evacuate the immediate area.

3. Turn off all local electrical equipment at the source.

4. Fight the fire in

one

of the following ways:

•

Smother the fire with a fire blanket.

•

Aim a CO

2

fire extinguisher at the base of the flames.

•

Aim a dry-powder fire extinguisher at the base of the flames.

«
...
9
10
11
12
13
...
»

Summary of Contents for VC350A








































































































































































































































































































































Reviews:

No comments

Related manuals for VC350A

Brand: Walker Bay Pages: 8

Brand: GE Pages: 802

Brand: iET Pages: 17

Brand: Barreto Pages: 20

Brand: Barreto Pages: 18

Brand: Backyard Discovery Pages: 41

Brand: iHealth Pages: 8

Brand: M-Audio Pages: 3

Brand: natus Pages: 20

Dantec Keypoint G4

Brand: natus Pages: 42

Brand: natus Pages: 149

Brand: VARISCO Pages: 24

Brand: Vari Lite Pages: 14

Brand: Vaniman Pages: 3

Brand: Martin Pages: 202

Brand: American DJ Pages: 12

Brand: aion Pages: 10

Brand: COOPS & FEATHERS Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands