Valco Cincinnati VC350A Manual Download Page 267 | Manualshive

Page: 267 / 327

background image

7-14

Valco Cincinnati, Inc.

Section 7 - Initial Setup

MC060 Manual/VC350AG AutoGlue Control System

minimum-speed potentiometer

Figure 7-8. Minimum-Speed Potentiometer

For manual mode only. To adjust the maximum-speed potentiometer (Figure
7-9), follow these steps:

1.

Switch the AutoGlue selector switch to the off position.

2.

Turn the glue flow knob on the hot-melt unit to the full clockwise
position.

3.

Adjust the maximum speed potentiometer to the desired motor
speed. (A clockwise rotation will increase the motor speed.)

WARNING!

WARNING!

WARNING!

WARNING!

WARNING! Do not exceed 180VDC armature voltage (circuit board

terminals A1 and A2). OTHERWISE, DEATH,
PERSONAL INJURY, OR EQUIPMENT DAMAGE
COULD OCCUR.

The minimum speed adjustment will
affect the maximum speed setting.
Therefore, it is necessary to readjust
the maximum speed after the minimum
speed has been adjusted. It may also
be necessary to repeat the operations
until both the minimum and maximum
speeds are set to the desired levels.

Maximum-Speed

Potentiometer

Minimum-Speed Potentiometer -
Continued

«
...
265
266
267
268
269
...
»

Summary of Contents for VC350A








































































































































































































































































































































Reviews:

No comments

Related manuals for VC350A

Brand: OMCA Pages: 72

Brand: Fein Pages: 248

Brand: ZF Pages: 30

Brand: Raymarine Pages: 111

Brand: OMCA Pages: 36

Brand: Salford Pages: 64

Brand: Bahco Pages: 9

Brand: made for movement Pages: 51

Brand: Datavideo Pages: 28

Brand: Mainca Pages: 21

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Dairyland Pages: 5

Brand: Eaton Pages: 16

RMQ-Titan C22-PV Series

Brand: Eaton Pages: 6

Brand: Eaton Pages: 98

Brand: Eaton Pages: 15

Brand: Federal Signal Corporation Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands