Valco Cincinnati VC350A Manual Download Page 39

Page: 39 / 327

Section 6

—

Installation

VC350A Flexoseal

System

Valco Cincinnati

6-22

Installing the Air Supply

The plant air system must supply at least 80 psi (6.5 bar) of clean, dry air to the Flexoseal

system. It may be

necessary to install low-pilot inlet glue valves in place of standard glue valves if 80 psi (6.5 bar) air is not available.

To connect the air supply, follow these steps:

1. Install plant air to the parent machine with a shutoff valve at the end of the line.

2. Mount the applicator air-pressure regulator in a convenient place near the shutoff valve.

Using 3/8" tubing, connect the regulator to the applicator air solenoid and the “AIR IN” port of the control
(Figure 6-24).

4. Using 1/4" tubing, connect the fluid pressure regulator to the “PRESSURE OUT” port

of the control.

5. Connect the output of the glue regulator to the glue valve.

Note!

Maximum pressure in = 100 psi. Pressures above 100 psi can cause damage to the pressure trans-
ducer.

Figure 6-24. Bottom View of VC350A Control

“AIR IN” port

“PRESSURE
OUT” port

Summary of Contents for VC350A








































































































































































































































































































































Search results

Summary of Contents for VC350A

Reviews:

Related manuals for VC350A

Brands by name

Popular brands

Valco Cincinnati VC350A, Manual

Search results

Summary of Contents for VC350A

Reviews:

Related manuals for VC350A

Brands by name

Popular brands