Valco Cincinnati VC350A Manual Download Page 278

Page: 278 / 327

8-10

Valco Cincinnati, Inc.

Section 8 - Operation

MC060 Manual/VC350AG AutoGlue Control System

11. If the parent machine is at rest and the pressure on the front

gauge is not on “0”, adjust the “zero” pot down to reach zero.

This adjustment should be made by
slowly backing the adjustment down.
Do not adjust the pot so far down that
the “decrease” LED remains on.

Figure 8-9. Fluid-Flow Control (EPC) Manifold

manifold

pressure-gauge port

pressure transducer

increase solenoid

decrease solenoid

Fluid-Flow Control (EPC) (original
version) - Continued

Summary of Contents for VC350A








































































































































































































































































































































Search results

Summary of Contents for VC350A

Reviews:

Related manuals for VC350A

Brands by name

Popular brands

Valco Cincinnati VC350A, Manual

Search results

Summary of Contents for VC350A

Reviews:

Related manuals for VC350A

Brands by name

Popular brands