manualshive.com logo in svg

Valco Cincinnati VC350A, Manual

The Valco Cincinnati VC350A user manual is available for free download at manualshive.com. This comprehensive manual provides clear instructions, diagrams, and troubleshooting tips to assist you in efficiently operating and maintaining your VC350A. Get your manual now to fully utilize the features of this exceptional product.

Share
Download
background image

B-3

Valco Cincinnati, Inc.

MC060 Manual/VC350AG AutoGlue Control System

Appendix B - Quick Start Guide

For best results, the wheel of the
encoder assembly should ride
on the bottom side of the belt on the
drive side.

When the BOARDRUNNER Glue Station is shipped, it is ready for a 4

th

panel (drive side) top-down installation. The scanner is initially mounted to
view the product in line with the glue valve. The gap adjustment is set so
that a single-walled product (approx. 3mm thick) can pass through the glue
station and remain in contact with the applicator head.

The Setup Process consists of the following steps:

1.

Mount the BOARDRUNNER glue station to the mounting rods.

2.

Install the applicator head onto the 900 valve.

3.

Purge all air from the glue line, then connect to the valve. Purge
the valve by activating the push button switch on the valve.

Scanner and valve cables must be
connected before any purging can
take place.

4.

Run adhesive through valve until no air is present in the line.

5.

Run the parent machine and Stop when product reaches the
glue station.

6.

Adjust the glue station vertically to ensure the product is level.

7.

To modify the ‘gap adjust’ (gap between the applicator head and
bearing bar guide), use the bottom hex nut found on the upper
left side of the BOARDRUNNER. Once the gap is set, use the
top hex nut to lock it.

8.

If a tab side (operator’s side) installation is required, reverse the
direction of the inlet guides and mount the scanner bracket,
valve bracket and bearing bar guide on the opposite side of the
BOARDRUNNER.

9.

The bearing can be adjusted (in and out) to optimize the glue
pattern by guiding the board into the applicator head. This keeps
the board in contact with the applicator head through the entire
gluing section.

Mounting the Encoder - Continued

Installing the

BOARDRUNNER Glue

Station

Summary of Contents for VC350A








































































































































































































































































































































Reviews:

No comments

Related manuals for VC350A

Landoll 2510 Series Operator'S Manual preview
2510 Series
Brand: Landoll Pages: 34
Taylor 490 Operator Training preview
490
Brand: Taylor Pages: 70
Raith 150 System Operation Manual preview
150
Brand: Raith Pages: 26
Kane 501C Manual preview
501C
Brand: Kane Pages: 16
NEC MD462OR Quick Reference Manual preview
MD462OR
Brand: NEC Pages: 44
AccuMed CMS-50D Manual preview
CMS-50D
Brand: AccuMed Pages: 14
TAS 3012 User Manual preview
3012
Brand: TAS Pages: 25
Cameo SCUBA User Manual preview
SCUBA
Brand: Cameo Pages: 64
Cameo OPUS Series User Manual preview
OPUS Series
Brand: Cameo Pages: 100
CAME PXTS4.3 Installer Manual preview
PXTS4.3
Brand: CAME Pages: 32
Vapotherm precision flow Operating Instructions Manual preview
precision flow
Brand: Vapotherm Pages: 32
Vanguard Instruments EZCT Operating Procedures Manual preview
EZCT
Brand: Vanguard Instruments Pages: 47
M-Audio Ozone User Manual preview
Ozone
Brand: M-Audio Pages: 48
M-Audio FireWire 410 Quick Start Manual preview
FireWire 410
Brand: M-Audio Pages: 19
M-Audio Fast Track Pro User Manual preview
Fast Track Pro
Brand: M-Audio Pages: 17
M-Audio MidAir User Manual preview
MidAir
Brand: M-Audio Pages: 18
M-Audio X-Session Guía De Inicio Rápido preview
X-Session
Brand: M-Audio Pages: 12
M-Audio X-Session User Manual preview
X-Session
Brand: M-Audio Pages: 20

Brands by name

Popular brands

Load more brands