Valco Cincinnati VC350A Manual Download Page 73

Page: 73 / 327

Section 10

—

Troubleshooting

VC350A Flexoseal

System

Valco Cincinnati

10-3

Problem

Possible Cause

Possible Solution

Glue Pattern, continued

16. Pattern length is

acceptable but the
pattern position shifts.

16a.

Scanner may be detecting a
machine’s sheet transporter
instead of the product.

16a.

Adjust the sensitivity of the
product scanner to detect
product a maximum of 2 inches
below normal product travel.

17. Pattern length and

position vary.

17a.

Encoder belt loose.

17b.

Gear is loose.

17c.

Parent machine drive is faulty.

17d.

Encoder is damaged.

17e.

Slippage of discs between the
folding belts.

17a.

Tighten encoder belt.

17b.

Tighten gear.

17c

Repair or replace parent
machine drive.

17d.

Repair or replace encoder.

17e.

Tighten folding belts.

18. Pattern skewed and

positioned too close to
the leading edge of the
product

18a.

Guide spring tension too high.

18b.

Not enough pressure between
folding belts.

18c.

Loose glue station.

18d.

Low panel boxes with deep slots
may be deforming the product.

18a.

Decrease guide-spring tension.

18b.

Increase pressure between
folding belts.

18c.

Tighten glue station.

18d.

Adjust belt tension.

19. Too much glue after the

parent machine is
stopped then restarted.

19a.

Glue pressure regulator may not
be closing properly

19a.

Check ball and seat for dirt.

19b.

Repair regulator.

19c.

Add a dump valve.

20. There is insufficient

glue at high speed.

20a.

Pressure regulator “T” handle
loose

20b.

Air system leak

20c.

Air system obstruction

20d.

EPC solenoids clogged

20e.

Defective air valve in the
transducer

20f.

EPC not adjusted

20a.

Tighten “T” handle lock nut.

20b

Repair the leak.

20c.

Clean the air system.

20d.

Clean EPC solenoids

20e.

Repair or replace air valve.

20f.

Adjust EPC-50 card

Summary of Contents for VC350A








































































































































































































































































































































Search results

Summary of Contents for VC350A

Reviews:

Related manuals for VC350A

Brands by name

Popular brands

Valco Cincinnati VC350A, Manual

Search results

Summary of Contents for VC350A

Reviews:

Related manuals for VC350A

Brands by name

Popular brands