Valco Cincinnati VC350A Manual Download Page 220 | Manualshive

Page: 220 / 327

background image

2-1

Valco Cincinnati, Inc.

SECTION 2 - SAFETY INFORMATION

SECTION 2 - SAFETY INFORMATION

SECTION 2 - SAFETY INFORMATION

SECTION 2 - SAFETY INFORMATION

SECTION 2 - SAFETY INFORMATION

General
Information

It is the purchaser’s responsibility to ensure that all local, county, state, and
national codes, regulations, rules, and laws relating to safety and safe
operating conditions are met and followed.

The best safeguard is trained personnel. The purchaser is responsible for
providing personnel who are adequately trained to install, operate, and
maintain Valco components and systems.

This section contains information that is essential to the safety of personnel.
Safety information is included throughout the rest of the manual as well. The
following safety conventions are used to indicate potential safety hazards:

WARNING!

WARNING!

WARNING!

WARNING!

WARNING! This symbol indicates the presence of un-insulated

dangerous voltage within the product’s enclosure. This
voltage may cause electrical shock or fire. FAILURE TO
OBSERVE WARNING MAY RESULT IN DEATH,
PERSONAL INJURY, AND/OR EQUIPMENT DAMAGE.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING! This convention is used to alert the user to important

installation, operation, and/or maintenance information.
FAILURE TO OBSERVE WARNING MAY RESULT IN
DEATH, PERSONAL INJURY, AND/OR EQUIPMENT
DAMAGE.

CAUTION!

CAUTION!

CAUTION!

CAUTION!

CAUTION! This convention is used to alert the user to important

installation, operation, and/or maintenance information.
FAILURE TO OBSERVE CAUTION MAY CAUSE
EQUIPMENT DAMAGE.

All personnel involved with the installation, operation, and maintenance of the
equipment must read and thoroughly understand the following warnings:

WARNING!

WARNING!

WARNING!

WARNING!

WARNING! Disconnect all power before opening the control.

OTHERWISE, DEATH OR PERSONAL INJURY
COULD OCCUR. Only qualified personnel should open
and service the control.

WARNING!

WARNING!

WARNING!

WARNING!

WARNING! Promptly repair or replace all worn or damaged

electrical wiring and equipment wires. OTHERWISE,
DEATH OR PERSONAL INJURY COULD OCCUR.

Warnings

«
...
218
219
220
221
222
...
»

Summary of Contents for VC350A








































































































































































































































































































































Reviews:

No comments

Related manuals for VC350A

Brand: Bartscher Pages: 22

Brand: Falcon Pages: 12

Brand: MacDon Pages: 89

Brand: Yates Pages: 2

Brand: JAC Pages: 100

Brand: Yamaha Pages: 50

Brand: A&D Pages: 30

Brand: 3M Pages: 48

Brand: 3M Pages: 19

Speedglas G5-01

Brand: 3M Pages: 62

Quickfit Nexus Exit

Brand: Thomas & Betts Pages: 2

Brand: ACCU-CHECK Pages: 104

Brand: GARANT Pages: 239

Brand: p-light Pages: 36

RIDA qLine ZG2601

Brand: R-Biopharm Pages: 23

Brand: K-SPORT Pages: 5

SeQual Eclipse 5

Brand: CAIRE Pages: 2

Brand: Cablexpert Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands