Hitachi SJ700-004LFU2, Instruction Manual

Page: 340 / 390

ModBus Data Listing
Append
ix
B
B–56
B042 — Torque limit (2) (reverse-
regenerating in 4-quadrant
mode)
R/W 0. to 200. (%), no (disable torque
limit) 132Ch 04908 0 to 200,
255= (no)
1 %
B043 — Torque limit (3) (reverse-
driving in 4-quadrant
mode)
R/W 0. to 200. (%), no (disable torque
limit) 132Dh 04909 0 to 200,
255= (no)
1 %
B044 — Torque limit (4) (forward-
regenerating in 4-quadrant
mode)
R/W 0. to 200. (%), no (disable torque
limit) 132Eh 04910 0 to 200,
255= (no)
1 %
B045 — Torque limit LADSTOP
enable
R/W 00 . Disable
01 . Enable 132Fh 04911 0, 1 —
B046 — Reverse Run protection
enable
R/W 00 . Disable
01 . Enable 1330h 04912 0, 1 —
— (Reserved) — — 1331h
to
1333h
04913
to
04915
— —
B050 — Controller deceleration and
stop on power loss
R/W 00 . Disable
01 . Constant decel to stop
02 . Constant DC voltage
control with resume
03 . Constant DC voltage
control 1334h 04916 0 to 3 —
B051 — DC bus voltage trigger
level during power loss
R/W Sets trigger for controlled decel-
eration and stop on power loss
function 1335h 04917 0 to 10000 0.1 V
B052 — Over-voltage threshold
during power loss
R/W Sets over-voltage threshold for
controlled deceleration function 1336h 04918 0 to 10000 0.1 V
B053 H Deceleration time setting
during power loss
R/W 0.01 to 99.99, 100.0 to 999.9,
1000 to 3600 (seconds) 1337h 04919 0 to
360000
0.01 sec.
B053 L R/W 1338h 04920
B054 — Initial output frequency
decrease during power loss
R/W Sets the initial decrease in output
frequency upon power loss 1339h 04921 0 to 1000 0.01 Hz
B055 — Proportional gain setting
for non-stop operation at
power loss
R/W 0.00 to 2.55 133Ah 04922 0 to 255 0.01
B056 — Integral time setting for
non-stop operation at
power loss
R/W 0.0 to 9.999, 10.00 to 65.55 133Bh 04923 0 to 65535 0.001
sec.
— (Reserved) — — 133Ch
to
133Eh
04924
to
04926
— —
B060 — [O] input max. limit level
of window comparator
R/W 0. to 100. (%)
Lower limit = B061 + B062 / 2 133Fh 04927 0 to 100 1 %
B061 — [O] input min. limit level
of window comparator
R/W 0. to 100. (%)
Lower limit = B060 – B062 / 2 1340h 04928 0 to 100 1 %
B062 — [O] input hysteresis width
of window comparator
R/W 0. to 10. (%)
Lower limit = B061 – B062 / 2 1341h 04929 0 to 10 1 %
B063 — [OI] input max. limit level
of window comparator
R/W 0. to 100. (%)
Lower limit = B064 + B066 / 2 1342h 04930 0 to 100 1 %
Holding Registers, “B” Group Fine Tuning Functions
Func. Code Name R/W Description
Network Data
Register
Range Res.
hex dec.