manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 91 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 91

IP Office Installation

Page 90

15-601042 Issue 20b (16 July 2009)

IP Office

5.10 Upgrading the Core Software

New IP500 control units are supplied with a basic level of software (4.0.0). That
software is sufficient to allow LAN network connect to the control unit in order to
then upgrade it to the level of IP Office software required.

 

Objective -

 Upgrade the control unit to IP Office 4.0 software.

 

Information Required

•

o

 

System Password

 - For a new or defaulted system this is password.

 

Tools Required

•

o

 

Manager PC

 - The Upgrade Wizard tool is part of the Manager

application.  

 

WARNINGS

 

•

Check IP Office Technical Bulletins

 

Check the latest IP Office Technical Bulletin for the IP Office software release before proceeding any further. It
may contain information relating to changes that occurred after this document was completed. Bulletins are
available from http://support.avaya.com.

•

Multiple Managers

 

If more than one copy of Manager is running it is possible for the IP Office to request BIN files from a different
Manager from the one that started the upgrade process. Ensure that only one copy of Manager is running when
upgrading an IP Office system.

 

Procedure: Upgrade Procedure

1. Using Manager, click 

 and receive the configuration from the IP Office. If not already done this action creates a

BOOTP entry in Manager for the IP Office system. This action also confirms communication between the Manager
PC and the IP Office.

2. Select 

File | Save Configuration As...

 and save a copy of the configuration file onto the PC. This action should

be completed before upgrading any IP Office system.  

3. Select 

File | Advanced | Upgrade

.

4. The UpgradeWiz is started and scans for IP Office unit using the Unit/Broadcast address. Adjust this address and

click Refresh if the expected modules are not shown.

5. For each the unit found, the UpgradeWiz displays the module type, its current version of software installed in the

unit and the software version of the .bin file that Manager has available.

6. For those units and modules where manager detects that it has a higher version available, the tick box next to the

unit or module is automatically selected.

7. For those modules which you want to upgrade, tick the check box. For modules where a later version of software

is available the check box may have already been automatically ticked.

8. Select 

Upgrade

.

9. The system password will be requested. Enter it and click 

OK

.

10.The bin files required are transferred to the system and stored in temporary memory.

11.Once all the files have been transferred, the upgrade wizard will prompt whether it okay to proceed with the

upgrade process. Select Yes to continue.

12.Each module being upgraded will delete its existing core software, restart and load the new software file that was

transferred. This process may take several minutes for each unit. Do not cancel or close the upgrade wizard while
this process is running.

13.Following the upgrade check that the upgrade wizard now shows that the selected units and modules have

upgraded. It may be necessary to select Refresh to update the information in the upgrade wizard display.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments