manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 373 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 373

IP Office Installation

Page 372

15-601042 Issue 20b (16 July 2009)

IP Office

The following additional power cords are available for use with the Avaya 1151D1 and 1151D2 power supply units.

1151D1/1151D2 Power Cord

SAP Code

USA

405362641

Europe

407786623

Australia and New Zealand

407786631

India

407790991

United Kingdom

407786599

Argentina

408161453

 

Cables

Cable

Description

SAP Code

Length

25-Way DTE Cable

Connects to a IP403 or IP406 V1 control unit. 25-Way D-type
plug to 9-way D-type socket.

700213432

2m/6'6''.

9-Way DTE Cable

Connects to an SOE, IP406 V2 or IP412 control unit. 9-Way
D-type plug to 9-way D-type socket.

–

2m/6'6''.

Structured Cabling DS Line
Cable

Connects from RJ45 sockets to RJ11 socketed DS and analog
phones.

700047871

4m/13'2''.

BRI/PRI Trunk Cable

Connects BRI/PRI trunk ports to the line providers network
termination point. RJ45 to RJ45. Red.

700213440

3m/9'10''.

IP500 BRI So Converter Cable

Provides the 100ohm terminating resistors necessary for an
IP500 BRI trunk daughter card port set to S-Bus mode. Also
provides the cable crossover. RJ45 plug to RJ45 socket. 

700458649

25cm/10"

Expansion Interconnect Cable

Connects the control unit to expansion modules (except
WAN3 modules). RJ45 to RJ45. Blue.

700213457

1m/3'3''.

Longer yellow cable version for use with IP500 4-Port
Expansion card. 

700472871

2m/6'6"

LAN Cable

Connects from IP Office LAN ports to IP devices. RJ45 to
RJ45. Grey.

700213481

3m/9'10''.

LAN Interconnect Cable

Connects WAN3 module to the control unit. Replace with a
LAN crossover cable for IP412 control units. Green.

700213465

1m/3'3''.

LAN Crossover Cable

Used for connection of IP devices to LAN ports on the IP412
control unit. Black

700213473

3m/9'10''.

V.24 WAN Cable

37-Way D-type plug to 25-way D-type plug.

700213416

3m/9'10''.

V.35 WAN Cable

37-Way D-type plug to 34-way MRAC plug.

700213424

3m/9'10''.

X.21 WAN Cable

37-Way D-type plug to 15-way D-type plug.

700213408

3m/9'10''.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments