manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 238 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 238

IP Office Installation

Page 237

15-601042 Issue 20b (16 July 2009)

IP Office

System Components: IP400 Trunk Cards

10.5.2 Analog Trunk Cards (ATM4)

The Analog Trunk card is also referred to as the "ATM4". It provides 4 RJ45 sockets for 

analog trunk connections

. The

card only supports loop-start trunks.  

The card is available in a number of locale specific variants as detailed below.

•

Power Failure Operation

 

There are no power failure extension connections provided for the analog trunk card.

•

 

WARNING

 

In all IP Office installations, any module or control unit using analog trunk connections must be connected to a 

functional earth

.

•

 

WARNING

 

Within the Republic of South Africa and in areas of high lightning risk, any module or control unit using analog trunk
connections must be connected to a 

protective ground

 and to 

surge protection equipment

.

 

ATM4 Trunk Cards

Country

SAP Code

SOE

IP406

V2

IP412 IP500

IP400 Analog 4 (Loop-
Start)

North and South
America

700185192

IP400 Analog 4 EU
(Loop-Start)

Europe

700241672

IP400 Analog 4 NZ
(Loop-Start)

New Zealand

700241706

•

These cards include two plastic stand off pillars for installation and a replacement blanking plate for the rear of IP400
control units.

10.5.3 BRI Trunk Cards

The BRI trunk card is also referred to as the "Quad BRI". It provides 4 RJ45 sockets for ETSI BRI trunk connections, with
each trunk supporting 2B+D channels.

•

The trunk card ports include 100 ohm termination.

Variant

Country

SAP Code

SOE

IP406

V2

IP412

IP500

IP400 BRI

All

 700185168

IP400 BRI 8 (UNI)

All except China

700262017

•

These cards include two plastic stand off pillars for installation and a replacement blanking plate for the rear of IP400
control units.  

•

For the IP500 control unit an IP500 Carrier Card is required, up to a maximum of 2 carrier cards.  

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments