Avaya IP Office Phone Manager Installation Manual Download Page 34 | Manualshive

Page: 34 / 411

Avaya IP Office Phone Manager Installation Manual Download Page 34

IP Office Installation

Page 33

15-601042 Issue 20b (16 July 2009)

IP Office

System Overview: Other Cards

2.10 Power Supplies

The IP500 has an internal power supply unit and so only requires a suitable locale specific power cord.

Small Office Edition, IP406 V2, IP412 control units and external expansion modules are all supplied with an external
power supply unit (PSU). These external power supply units include an integral 1.5 meter lead for connection to the
control unit or expansion module. A

power cord

for connection from the PSU to the power outlet is not included as this

varies by locale. The appropriate power cord must be ordered separately or sourced locally.

Additional power supply units are required for 4450, EU24, XM24 and T3 DSS add-on modules and may also be required
for 4600 Series/5600 Series IP phones.

Area

Type

Used on:

Connector Type

IP Office Control
Units and
External
Expansion
Modules

40W PSU

Analog, Digital Station V1, Phone V1.

IEC60320 C7

45W Earthed
PSU

Small Office Edition.

IEC60320 C13

60W Earthed
PSU

IP406 V2, IP412, IP400 Digital Station V2, IP400 Phone V2,
IP400 So8, IP400 WAN3 10/100,
IP500 Phone 30, IP500 Digital Station 30.

IP Phones and
Phone Add-Ons

1151D1

All phones with XM24 Phone add-ons.
All phones with EU24/EU24BL Phone add-ons unless using
Class 3 PoE.
4600 and 56000 Series IP Phones when not using a PoE.

1151D2

1600PWR 5V

Plug-top PSU used with 1600 Series phones on IP Office
when not being power using PoE.

Various country
variants.

•

Some units previously supplied with a 40W unearthed PSU are now approved for and supplied with a 60W earthed
PSU. That changes affects the IP412, So8 and WAN3 10/100 units.

•

The 1151D2 is the same as the 1151D1 except that it includes a backup battery that is charged during normal
operation. This can provide typically 15 minutes backup at maximum load (20 Watts) and up to 8 hours at light load (2
Watts).

•

Avaya 4600 Series and 5600 Series can use IEEE 802.3af Power over Ethernet (PoE) power supplies. Refer to the IP
Office IP Phone Installation Manual for full details.

«
...
32
33
34
35
36
...
»

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments