manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 237 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 237

IP Office Installation

Page 236

15-601042 Issue 20b (16 July 2009)

IP Office

10.5.1 Analog Trunk Card Uni (ATM4U)

This card supersedes the previous Analog Trunk cards and is referred to as the "ATM4U". It can be identified by a label
on the base of the card.

The card is supported on IP Office software 2.1(36) and higher. Unlike the previous ATM4 card, the same ATM4U card
variant can be used in all locales.

For systems running IP Office software 3.1 or higher, the echo cancellation used on each trunk can be switched off or on
(16ms).

The card provides 4 RJ45 sockets for 

analog trunk connections

. The card only supports loop-start trunks. For ground-

start trunks an 

Analog Trunk expansion module

 should be used.

•

Power Failure Operation

 

There are no power failure extension connections provided for the analog trunk card. If this is a requirement, the
ATM16 expansion module should be used.

•

 

WARNING

 

In all IP Office installations, any module or control unit using analog trunk connections must be connected to a 

functional earth

.

•

 

WARNING

 

Within the Republic of South Africa and in areas of high lightning risk, any module or control unit using analog trunk
connections must be connected to a 

protective ground

 and to 

surge protection equipment

.

ATM4U Trunk Card

Country

SAP Code

SOE

IP406

V2

IP412

IP500

ATM4 Uni (Loop-Start)

All

700359938

•

The card include two plastic stand off pillars for installation and a replacement blanking plate for the rear of IP400
control units.

•

For the IP500 control unit an IP500 Carrier Card is required, up to a maximum of 2 carrier cards.

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments