Home
/
Avaya
/
IP Office Phone Manager
/
Installation Manual

Avaya IP Office Phone Manager, Installation Manual, Page: 125 / 411

Share

Page: 125 / 411

Avaya IP Office Phone Manager Installation Manual Download Page 125

IP Office Installation

Page 124

15-601042 Issue 20b (16 July 2009)

IP Office

Grounding E1R2 Coaxial Connections

E1R2 coaxial trunk cards must be grounded correctly and require the IP Office control unit to be connected to a
protective ground.

Normally the ends of one connection is grounded. For example, if the exchange Tx1 is grounded, the IP Office Rx1 should
also be grounded. However this must be confirmed with the line provider to establish which ends they want grounded.

Procedure

1. Use the two jumpers supplied with the card, match the ground

selection of the line provider. For example, if the line provider
wants the IP Office Rx1 grounded, place a jumper across the
two Rx1 pins of jumper block J6.

2. Connect the ground strap spade end (B) to the spade

connection on the board.

3. Connect the other end of the ground strap (C) to the blanking

plate using the long securing screw supplied with the card.

4. Ensure that the coaxial connector ports are locked to the

blanking plate using the nuts provided.

5. Continue with trunk card installation as in

Stage 9a.

«
...
123
124
125
126
127
...
»

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments