manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 240 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 240

IP Office Installation

Page 239

15-601042 Issue 20b (16 July 2009)

IP Office

System Components: IP400 Trunk Cards

10.5.6 WAN Trunk Card

This trunk card provides a single 37-way D-type 

WAN port

.

WAN Cards

Country

SAP Code

SOE

IP406

V2

IP412

IP500

IP400 WAN Expansion

All

700289713

•

The card is supplied with two plastic stand off pillars for installation and a replacement rear panel for the Small Office
Edition control unit.

 

10.5.7 E1R2 PRI Trunk Cards

These cards support E1 trunks with R2 signalling. Each trunk provides up to 30B+D channels.

E1R2 PRI trunk cards are available with either RJ45 or coaxial cable connectors.

E1R2PRI trunk Cards

Country

SAP Code

SOE

IP406

V2

IP412 IP500

IP400 PRI 30 E1R2 RJ45

CALA, Korea, China

700241631

IP400 PRI 60 E1R2 RJ45

700241649

IP400 PRI 30 E1R2 COAX

CALA

700241656

IP400 PRI 60 E1R2 COAX

700241664

•

These cards include two plastic stand off pillars for installation and a replacement blanking plate for the rear of IP400
control units.

•

For E1R2 coaxial card, a ground-jumper cable and coaxial connector locking rings are included.

•

For dual port cards the IP406 V2 only supports a single dual card in Slot A.  

•

For the IP500 control unit an IP500 Carrier Card is required, up to a maximum of 2 carrier cards.

 

E1R2 coax trunk cards must be grounded correctly and require the IP Office control unit to be connected to a protective
ground.  Normally the ends of one connection is grounded. For example, if the exchange Tx1 is grounded, the IP Office
Rx1 should also be grounded. However this must be confirmed with the line provider to establish which ends they want
grounded.

 

1. Connect the ground strap spade end (B) supplied with the card to the spade connection on the card and the other end

(C) to the chassis with the long securing screw also supplied with the card.

2. Use the two jumpers supplied with the card, match the ground selection of the line provider. For example, if the line

provider has grounded their Tx1, place a jumper across the two Rx1 pins of jumper block J6.

 

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments