Avaya IP Office Phone Manager Installation Manual Download Page 122

Page: 122 / 411

IP Office Installation

Page 121

15-601042 Issue 20b (16 July 2009)

IP Office

IP400 Basic Installation: Fitting Modem Cards

Procedure: Installing Modem Cards

1. Check that correct card has been supplied.

2. Ensure that you are wearing a anti-static wrist strap

connected to a suitable ground point.

3. Remove the 7 screws fixing the IP Office control unit

cover and slide the cover off the unit.

4. Locate the position for the card and its jumper block.

5. Using the card as a template locate the two holes in the

control unit circuit board. Insert the stand off pillars
into these holes.

6. Using minimal force and checking that the pins are

correctly located, push the card onto the jumper block
and stand off pillars.

7. If other cards are being fitted, proceed to

Fitting Trunk

Cards

8. Slide the control unit cover back on and replace the

cover screws.

9. Reapply power to the control unit and check that it

restarts correctly.

10.Using the IP Office Monitor application, confirm that

the correct number of modem channels are now
reported. They are shown by the value MDM= when
Monitor first connects to the control unit.

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Search results

Summary of Contents for IP Office Phone Manager

Reviews:

Avaya IP Office Phone Manager, Installation Manual, Page: 122 / 411

Search results

Summary of Contents for IP Office Phone Manager

Reviews: