manualshive.com logo in svg

Avaya IP Office Phone Manager, Installation Manual, Page: 341 / 411

Share
Download
Avaya IP Office Phone Manager Installation Manual Download Page 341

IP Office Installation

Page 340

15-601042 Issue 20b (16 July 2009)

IP Office

10.11 Licence Keys

License shows the name as it appears in the IP Office configuration. RFA Name is the name used for the orderable item. 

License

Description

RFA Name

SAP

Advanced Small
Community
Networking

This license is used to enable remote hot desking, advertising
hunt groups and distributed hunt groups within a Small
Community Network. 

•

For remote hot desking a license is required on the
system to which a user hot desks. 

•

For distributed and advertised hunt groups a license is
required on each system. 

IPO LIC ADVANCED
NTWKG

202966

SIP Trunk Channels

These licenses are used to configure the maximum number of
simultaneous SIP trunk calls supported.

IPO LIC SIP
TRNK RFA

1

202967

5

202968

10

202969

20

202970

DECT Integration
(ports)

Enables enhanced DECT integration with the IP Office system.
Used with Compact DECT and DECT DCU. Not used with Avaya
IP DECT.

IP400 CTI
DECT

8

171989

16

174457

24

174458

Conferencing Center

Enables the IP Office Conferencing Center application.

IP400 Conferencing
Center

182302

SoftConsole (users)

Adds one additional SoftConsole user. A maximum of four
SoftConsole user can be licensed.

IP400 SoftConsole

171987

Compact Business
Center

Enables the CBC application for one user.

IP400 CBC

171993

Small Office Edition
WiFi

Enables use of the wireless card with the Small Office Edition
control unit.

IP400 Access Point

182197

Microsoft CRM
Integration (users)

Allows operation between IP Office and MS-CRM server and
clients.

IP400 Microsoft CRM
Intgr

180588

IPSec Tunneling

Enables the IP Office to initiate and terminate IPSec and L2TP
tunnels.

IP400 IPSec VPN

182301

Mobility Features

Enables the use of the IP Office 3.2+ mobile twinning features. 

•

For IP Office 4.2+, the 

Mobile Twinning

 license is now called

the 

Mobility Features

 license, reflecting the fact that it can

be used for Mobile Call Control and one-X Mobile Client
support in addition to just mobile twinning. The mode of
license operation has also changed. 

•

Prior to IP Office 4.2, the license was only consumed by
users who had Mobile Twinning enabled. For IP Office 4.2
+ it is consumed by a user when they are configured for
any of the mobility features, including mobile twinning
even if they have turned mobile twinning off.

•

For IP Office 4.2+, the license moves with hot desking
users including within a Small Community Network. 

Mobile
Twinning

1

195569

5

195570

10

195571

20

195572

50

195573

VPN IP Extensions

IP Office 4.1+. Used in conjunction with the Extension | VoIP |
VPN Phone Allowed setting to license the operation of 46XX
Series and 56XX Series phones using VPNremote firmware.  

VPN Phone

1

213980

5

213981

10

213982

25

213983

50

213984

100

213985

Unlimite
d

213986

Trial 10 213987

IP End-points

Controls the number of 3rd party H323 devices supported by IP
Office. No license is required for Avaya 4600 and 5600 series
telephones. IP enabled Phone Manager Pro is licensed
separately.
For IP Office 5.0+, this license is also used to enable SIP
extensions. 

IP400 IP
Endpoint

1

174956

5

174957

10

174958

20

174959

50

174960

100

174961

Trial 5

227040

Summary of Contents for IP Office Phone Manager




























































































































































































































































































































































































































Reviews:

No comments